Hot Bodies Cyclone
#6586
Tech Elite
iTrader: (24)
Originally Posted by Tez
Found it.
whats the diference between the hara spool and the new one, they look very similar to me, also i thought it had delrin parts in it??
whats the diference between the hara spool and the new one, they look very similar to me, also i thought it had delrin parts in it??
#6587
Tech Elite
iTrader: (24)
Originally Posted by wyl03
which online shops have the most HB parts?
stormer seems to have most things "on order"
stormer seems to have most things "on order"
http://www.towerhobbies.com/
Speedtech
http://www.speedtechrc.com/store/ebcategory.asp?id=28
Champ RC
http://rc-champ.co.jp/
Precision RC
http://www.precisionrc.com/nv/car/pr...540&cat_id=952
to name a few.....
#6590
Tech Elite
iTrader: (24)
Originally Posted by pinggoy
guys. how do you strap lipo packs (orion 3200) on the cyclone? just strap it with tape and its good to go?? plus on which side will you put weights on the lipo to even out the weight of 4200.. (on top? left side? right side?) thanx
That depends on what servo, receiver, transponder, speed controller and motor you're running? In my Clone, I have a 25g weights on the left side of the chassis against the weight of the 4200's.
With Lipo's I'd expect the weights to go on the right side of the chassis as the lipo's will be considerably lighter.
I borrow these from a friend to balance my chassis. The Clone has pre-drilled holes for them in the bottom deck.
http://www.hudy.net/xhudy/products/p...3&kategoria=64
#6591
Stew you have a PM
#6592
Tech Master
Hey all,
I broke TWO (!!) Servo savers yesterday. Any ideas?? I even ran the 2nd one alittle loose.
I broke TWO (!!) Servo savers yesterday. Any ideas?? I even ran the 2nd one alittle loose.
#6593
Only thing i can think of is them being to tight.
Saying that, i have run cars in the past with no servo saver (TC3, TC4....but they break before the servo has chance to get damaged )
Were they broken due to really hard hits or just to much stress?
Saying that, i have run cars in the past with no servo saver (TC3, TC4....but they break before the servo has chance to get damaged )
Were they broken due to really hard hits or just to much stress?
#6594
Tech Master
I was running a BMI chassis on medium bite carpet. I bounced off the corners and slammed into the boards. I tried running the servo saver alittle loose, but the treads are just so thin! I broke one with not even a scratch on the body. It really wasnt a hard hit. The suspension was strait and the car was un-tweeked.
#6595
Originally Posted by Static_racing
I was running a BMI chassis on medium bite carpet. I bounced off the corners and slammed into the boards. I tried running the servo saver alittle loose, but the treads are just so thin! I broke one with not even a scratch on the body. It really wasnt a hard hit. The suspension was strait and the car was un-tweeked.
I've hit my share of stuff with both my Cyclones and I haven't broke a servo saver. That's the last thing I would expect to break. I have broken a few steering blocks though.
#6596
Tech Master
'dang Steak!! What rock did you crawl out from?! Gave the porn a break for a minute huh?
Man, it was so fusterating. In the 3rd qual I checked out and had 18 seconds to go. I was on a 24 5:06 pace, which would have put me in the top of the "B" when I broke the car. No parts at the track and I had about a thousand of every part BUT that!!! Man, my luck at big races sucks! My car was SOOOO GOOD in that last qual. If was BALLISTIC!!!!
Lemme know whats new with you. I talked to Anthony and he said there were some line-up changes
Man, it was so fusterating. In the 3rd qual I checked out and had 18 seconds to go. I was on a 24 5:06 pace, which would have put me in the top of the "B" when I broke the car. No parts at the track and I had about a thousand of every part BUT that!!! Man, my luck at big races sucks! My car was SOOOO GOOD in that last qual. If was BALLISTIC!!!!
Lemme know whats new with you. I talked to Anthony and he said there were some line-up changes
#6597
Originally Posted by Static_racing
'dang Steak!! What rock did you crawl out from?! Gave the porn a break for a minute huh?
Man, it was so fusterating. In the 3rd qual I checked out and had 18 seconds to go. I was on a 24 5:06 pace, which would have put me in the top of the "B" when I broke the car. No parts at the track and I had about a thousand of every part BUT that!!! Man, my luck at big races sucks! My car was SOOOO GOOD in that last qual. If was BALLISTIC!!!!
Lemme know whats new with you. I talked to Anthony and he said there were some line-up changes
Man, it was so fusterating. In the 3rd qual I checked out and had 18 seconds to go. I was on a 24 5:06 pace, which would have put me in the top of the "B" when I broke the car. No parts at the track and I had about a thousand of every part BUT that!!! Man, my luck at big races sucks! My car was SOOOO GOOD in that last qual. If was BALLISTIC!!!!
Lemme know whats new with you. I talked to Anthony and he said there were some line-up changes
Watching the Novak Race and watching the Eagles is more important than you breaking your car.
And as far as line-up changes... I can only assume you are talking what car I am running now.
#6598
Tech Master
Just when I though I had a handle on it all, Anthony told me I was on up on the latest.
#6599
I know how you feel I also broke 2 about a week ago. It just seems like where the bearing fits in is just too thin around the threads? Any suggestions guys.
#6600
Tech Master
Originally Posted by jeremymoemorris
I know how you feel I also broke 2 about a week ago. It just seems like where the bearing fits in is just too thin around the threads? Any suggestions guys.