Hot Bodies Cyclone
Tech Rookie
The problem is, WHICH combination to use ... i mean, here at the forums all people says spurs 70 - 74 ... and pinions on the 33 - 36 range ... and if i see the setups online from cyclone S users on other sites, they say use 100++ spurs and 40+ pinions ... so, where to go ?
Its for 13.5 brushless 6 cells nimh ... asphalt rubber
cya,
Pat
Its for 13.5 brushless 6 cells nimh ... asphalt rubber
cya,
Pat
Last summer i was using 91 and 51 gears for my Cyclone S(with internal ratio 2.4375).
I don't know condition of your track, but if there is a lot of small stones/dust then i would suggest you to go with 48p gears, as they will strip less. My personal experience with this, as last year I stripped some spurs/pinions due to this fact(was using 64p ones)
Last edited by janux; 04-11-2009 at 12:48 AM.
Tech Elite
iTrader: (1)
Well guys, downhere in my country its impossible to get locally pinions and spurs so i ordered from rcmart.com this ones :
Kawada brand spurs 66T, 68T and 70T
Kawada brand pinions 32T, 34T and 36T
All in 48 pitch, hope to nail it with it because if not i have to reorder and wait 3 weeks lol !!
thanks for all guys, your posts and private messages has been great help on this my first time on electric touring ...
cya !!
Pat
Kawada brand spurs 66T, 68T and 70T
Kawada brand pinions 32T, 34T and 36T
All in 48 pitch, hope to nail it with it because if not i have to reorder and wait 3 weeks lol !!
thanks for all guys, your posts and private messages has been great help on this my first time on electric touring ...
cya !!
Pat
Tech Adept
iTrader: (1)
fdr for 3.5bl
hey guys need a fdr to start with for my new redline 3.5,just sent my entry off for reedy,so you know the venue,i'm running my same cyclone from the 06 reedy race,well almost the same ,well i'm sure a few of the orignal parts are still on it,its a hara ed.with 3 racing hopups and newer tc bulk heads,with newer 18t center pulleys&belts.been running 10.5 lately just went brushless 7 months ago,any sugestions or starting points would be helpful,thanks!
Tech Fanatic
iTrader: (66)
hara ed. set up
I have a hara ed. cyclone and I'm looking for a good strarting set up for rubber tire carpet with a 13.5. Thanks.
Tech Adept
iTrader: (1)
4 year old tool!
here.s the old girl,it was one of the first batch's of haras that came out, i got it about 4 months before the 06 reedy race!but of course lke all cyclones they morf. over time
R/C Tech Elite Member
iTrader: (101)
Nice car, but whats up with that steering servo? Looks totally different.....
Tech Adept
iTrader: (1)
3002 pplleeaassee, its an old 9550 futaba w a chunk of lexan to hold my amb pt
R/C Tech Elite Member
iTrader: (101)
I wasnt looking close enough this morning
It looked like the servo horn was coming from the side of the servo...my bad
It looked like the servo horn was coming from the side of the servo...my bad
Tech Champion
iTrader: (13)
I have a local race I'm going to this weekend. We have recently lost Seattle Indoor Raceway as the primary indoor racing venue for on road racing. Due to some dedicated racers, they have created a club that races in a old naval base blimp hangar in Seattle, Wa. They are havign their first "special event" race this weekend on the 11th, so I'm going to go support the new club and race with them.
Check it out here:
http://www.seattlercracers.com
There is a possibility I'll be down later this month for some testing though. Some of the Canadians are going to kidnapp me on their way down haha.
-Korey
Check it out here:
http://www.seattlercracers.com
There is a possibility I'll be down later this month for some testing though. Some of the Canadians are going to kidnapp me on their way down haha.
-Korey
Front:
Oil: Losi 60wt
Spring: HPI Pro 4 Gold
Piston: HB 1.1mm 3 hole piston
Shock position: 2 on tower, 2 on arm
Camber Link Position: Long, with 3mm under inner pivot
Camber: 2 deg
Caster: 4 deg
Swaybar: 1.4mm
Toe in/out: 0 deg
Wheelbase: 2mm in front of arm, .7mm shim behind it (a little shorter than stock)
Ride Height: 4.5mm
Droop: 1.75mm past ride height
Front toe block: 1.5 deg
Shims under suspensiopn blocks: 1.5mm all around
Wheel Hex: std
Ackerman: 4mm
Front Drive: Spool
Other: ATC posts with 2mm shim instead of oring
Rear:
Oil: Losi 60wt
Spring: HPI Pro 4 Blue
Piston: HB 1.1mm 3 hole
Shock position: 2 on tower, 3 on arm
Camber link position: Long on bulkhead, short on rear hub, with 2mm under the inner pivot
Camber: 2 deg
Droop: 2.25mm past ride height
Swaybar: 1.2mm
Rear Toe block: 3 deg
shims under suspension blocks: 1.5mm
Wheelbase: Kit Settings
Tires: Speedmind/Sorex 28R premounts
Traction Compound: Paragon Ground Effects, full front and rear for 20 min
Body: Protoform Mazdaspeed 6 mounted a tick forward
-Korey
Last edited by billythekid; 04-17-2009 at 02:50 PM.
Tech Adept
iTrader: (1)
anyone
hay guys anyone have a starting point for gearing on a 3.5 brushless,gonna test sunday at a club race at a local car show,i need a starting point,i,m running a tekin rs pro&matching redline 3.5 thaks guys.
Tech Master
iTrader: (47)
Assuming your running 5 cell, gear around 8.5-8.6 and check your motor temps.
Tech Adept
iTrader: (1)
7.4lipo
no 5cell i,m throuth with nimh/lipo baby,i'm running checkpoint 5400s but i'm thinking of getting the new 3600 checkpoint that just came out its 30c.does it make much difference between 5cell and 7.4lipo on fdr?
Tech Champion
iTrader: (32)