wwddww34

iTrader: (9)

The Club ESC is 1s capable. I checked Novak's web page for the Club ESC. Down at the bottom of the page is a list of Club ESC Specifications:

• Fwd/Brk/Rev: F / B (no reverse)
• Input Cells: 1*-2S LiPo only
• Size: 1.15” x 0.95” x 0.66” (29.0 x 24.3 x 16.8 mm)
• Weight (w/o wires): 0.69 oz. (19.5 g)
• On-Resistance: 0.0011 ohms @ 25°C trans. temp.
• Motor Compatibility 540-size: 17.5 -turn or higher sensored brushless motor; 380-size: All Novak Three-80 sensored brushless motors
• BEC: 6.0 volts DC / 2.0 amps
• Wire Size: 14G Super-Flex Copper-Strand Silicone Wire
• Battery/Motor Plugs Tamiya-style battery & gold-plated Bullet motor plugs factory installed

*1S Booster Module is recommended
__________________________________________________ ___________________

---->http://www.rctech.net/forum/texas-ra...obby-shop.html

mkiiina

iTrader: (71)

hey DD, I'll be there this weekend (like last weekend) to rep the VTA class. Hopefully we will have a larger turn out.

wwddww34

iTrader: (9)

Cool! If we can get just 1 more person to show up on Saturday then we can have a VTA class.
__________________________________________________ ___________________

---->http://www.rctech.net/forum/texas-ra...obby-shop.html

maddysdaddy

iTrader: (40)

TC4 longer front body posts? pop a 1/4 inch spacer in between the stock post and plate with a longer screw, or does anyone know if AE part 8818 fits nice and easy? stock posts are a little too short under the mustang body...

Stanfsu

iTrader: (294)

All - Thanks for your feedback on the motor/esc combo. Very helpful. Might decide to get the edge combo for an extra $40.

Stan

k_bojar

iTrader: (30)

in the long run, it might be worth the $$...sometimes it don't pay to always buy the cheapest equipment out there - even when its from the same manufacturer

snoopyrc

iTrader: (2)

What is the scoop on this? Its legal but not released into the "Wild" yet?

wwddww34

iTrader: (9)

That's exactly what I'm thinking. It's already on the USVTA list, but you can't buy one yet.

nashrcracer

iTrader: (1)

the $40 is well worth the money just to get the ballistic which is rebuildable the bonus is the Edge speed control is included.

DARKSIDE

iTrader: (2)

its on the list, and testing was done....but if SP doesnt have it on the shelf...

Approved ESCs:
Novak-
Club Brushless ESC (#1852)
EDGE 2S Brushless ESC (#1850, 1851)
Mongoose Micro Brushless/Brush ESC (#1718)
GTB 2 Racing w/X-Drive (#1749)
GTB 2 Racing w/X-Drive- Low Profile (#1748)
GTB 2 Sportsman Racing Brushless ESC (#1708, 1709)
GTB series part numbers:1710, 1711
Havoc series part numbers:1732, 1733, 1735
Slyder part number: 1712
XBR (DISCONTINUED) part number:1720

LRP
A.i. Brushless Reverse part numbers: LRP80100, LRP80150

SPEED PASSION
Cirtix Stock Club Race ESC part number: 12280
Reventon Stock Club Race part number:SP000048

dfiantii

iTrader: (18)

Maybe they should not allow it to go on the list until the company actually has stock to sell.

DARKSIDE

iTrader: (2)

maybe...but maybe the 1st batch is already sold....and rd 2 is coming...but getting it approved is very much needed before its "out there" so ppl dont just "think" its legal...example...GTB2 Xdrive...

testing things before is better than waiting for ppl make mistakes and waste money

snoopyrc

iTrader: (2)

I dont see the need to withold it from the list just because its not available yet. Its tested its approved its on the list. If you happen to work in the SP factory (or is it Hobby Wing?) Then by all means sneak one out under your jacket and race it like you stole it. Which in this case you would have.

Meradin

iTrader: (19)

Not sure if I am stepping on any toes here. I have had a few PM's and a few emails about where I got the numbers and stickers for a few of my recent VTA bodies and logos.

I cut them using my plotter. I have been cutting number badges and logos for VTA racers here locally for a while. If you need some let me know. PM me for details so we don't clog this thread up with for sale discussions.

If this is a violation or not in the spirit of this thread, let me know and I will delete the post. Just thought I could add to the VTA thread and make it a bit easier for people to get rule compliant.

Here is an example of some recent numbers I did up. All in vinyl so there are just peel and stick. I can do them in multiple colors and different styles as well.

IndyHobbies.com

Those look really nice Mera'din. Something tells me any $$ you make will just go back into the hobby, right!