Exotek F1R
#1351
Tech Apprentice
Mike, any idea when we might expect the servo saver plate and the machined front damper tubes to be available?
...now I see the damper tubes for 1st week of Feb, still wondering on the plate... maybe around the same time as they're "in production"?
...now I see the damper tubes for 1st week of Feb, still wondering on the plate... maybe around the same time as they're "in production"?
Last edited by kineteks; 01-19-2015 at 09:17 AM. Reason: need to read posts more carefully
#1353
Tech Champion
iTrader: (15)
Not that I know of. My 'to do' list is about 3 pages long so cannot make a custom pdf doc at this time.
Are there any skilled pdf set up sheet makers our there for hire
Yes should be first week of Feb for both. Note the servo plate is for the xray servo saver only. My experience is that the Tamiya servo saver is too soft.
The Exotek adjustable arms will easily surpass any angles of the stock 104 arms if built correctly. Do you have a pic of your assembly?
Hi,
Too much caster will jack the car over and cause the inside wheels to lift. 5° is what I'd be at.
What front lube are you using? But make sure you have enough lube in the front damper to slow down the front suspension and try the outer hole on the front tower.
I'm not sure if you have tried it but a lot of carpet guys (Tamiya cars) are using the f103 diff thrust washer with tamiya awg grease to prevent 'diffing' on carpet.
Are there any skilled pdf set up sheet makers our there for hire
Thanks Aaron
Front of car = 4mm ride height, 8 deg castor, 1.5 camber, 1 deg toe out, stiff front springs ( kit) .5mm of droop as per instructions
Short wheel base, center shock will be 30wt I believe, 1mm pod droop, side springs associated white, thick crc lube in damper tubes, center shock location towards the rear of the chassis ( back hole )
Front of car = 4mm ride height, 8 deg castor, 1.5 camber, 1 deg toe out, stiff front springs ( kit) .5mm of droop as per instructions
Short wheel base, center shock will be 30wt I believe, 1mm pod droop, side springs associated white, thick crc lube in damper tubes, center shock location towards the rear of the chassis ( back hole )
Too much caster will jack the car over and cause the inside wheels to lift. 5° is what I'd be at.
What front lube are you using? But make sure you have enough lube in the front damper to slow down the front suspension and try the outer hole on the front tower.
I'm not sure if you have tried it but a lot of carpet guys (Tamiya cars) are using the f103 diff thrust washer with tamiya awg grease to prevent 'diffing' on carpet.
#1354
Very positive testing with the IFS yesterday on the F1R2, really effortless to drive and less "on the edge" feel of normal F1 cars. Looking forward to the machined damper tubes so we don't have to run crazy thick lube.
#1355
It's not fancy but Ive attached PDF's of my setup for the IFS. Let me know If I missed something or something else that needs to be on there and I can add it as we go
Aaron
Aaron
#1357
That's awesome Aaron.
May be asking a lot of you but do you by chance have something similar for the exotek F1R2 rear end too?
Thanks again.
May be asking a lot of you but do you by chance have something similar for the exotek F1R2 rear end too?
Thanks again.
#1358
I don't have anything for the rest of the car yet but I can make something similar like this during the week and post it up for everyone
#1359
Awesome man!
That would be great. I am sure everyone will appreciate it.
That would be great. I am sure everyone will appreciate it.
#1360
Been reading about the new front end...
i've got an F1R and getting the itch to mount the new front end in it...
wonder will it be possible to run normal 2 cell touring LiPo after the new front end?
i've got an F1R and getting the itch to mount the new front end in it...
wonder will it be possible to run normal 2 cell touring LiPo after the new front end?
#1361
You can but you need to purchase the side winglets to mount the ESC/RX.
#1362
hold on... the rear section is messed up lol revising now
#1363
here is the revised blank setup sheet... sorry
#1365
That is awesome Aaron, thanks a million mate. It looks great.
Sorry if this is too much to ask of you but would you mind posting your setup?
Or Mike any chance of getting your setup too using Aaron's setup sheet.
Thanks guys.
Sorry if this is too much to ask of you but would you mind posting your setup?
Or Mike any chance of getting your setup too using Aaron's setup sheet.
Thanks guys.