Traction Compounds for Parking Lots
#1
Traction Compounds for Parking Lots
This weekend we tried a few traction compounds. The one we liked best in the morning was the Paragon Ground Effects on our rubber tires. But as the day went on and the tempature came up it seemed to stop working and then what we found worked best was a bit of motor spray to clean the tires and leave them be. Just wondering what other people are using on their tires to get the most performance from them?
Thanks!
Thanks!
#2
Tech Elite
iTrader: (12)
Jared- we run on a medium traction p/l, and I have found the exact same thing you found- as the track gets really hot, the traction compound quits working.
Try this: when the track temp get on up there, instead of letting the traction compound sit on the tires, put it on, wait a few seconds, then wipe it right off. You are basically doing the same thing- just cleaning them, but you are also putting a little compound into the outside skin of the tire. If you let them sit with compound on them (in the heat), you will have one greasy, skating, donut cutting ride! lol
Try this: when the track temp get on up there, instead of letting the traction compound sit on the tires, put it on, wait a few seconds, then wipe it right off. You are basically doing the same thing- just cleaning them, but you are also putting a little compound into the outside skin of the tire. If you let them sit with compound on them (in the heat), you will have one greasy, skating, donut cutting ride! lol
#4
It's hard to find, but I use rubber roller cleaner. I just spray it on a rag and wipe the tires clean with it. I also use WD-40 using the same method. Both products clean the tires and at the same time rejuvents the rubber.
#6
Are you talking about the DEATH GRIP TIRE CLEANER,RUBBER by TRINITY [TRI4064] ??
#9
Tech Elite
iTrader: (16)
The rubber roller cleaner and conditioner that sponger and Tres mentioned sounds a lot like pinch roller cleaner. It's some amazing stuff. It can be hard to find, but if there's a good music store in your area that sells recording equipment, you can find it there, under the Tascam brand. Just ask for "Tascam RC-2 Rubber Cleaner". Way back in the early days of electric (1979 or so) we used to get it at stereo shops, it was sold by Teac as a pinch roller conditioner for tape decks.
I'm pretty sure it's the same stuff that the IBM guy gets, but I might just hunt up an IBM guy to check their version out. One thing... this stuff does a have a strong nasty odor. If the smell of Paragon bothers you, this stuff may really offend you.
Trips
I'm pretty sure it's the same stuff that the IBM guy gets, but I might just hunt up an IBM guy to check their version out. One thing... this stuff does a have a strong nasty odor. If the smell of Paragon bothers you, this stuff may really offend you.
Trips
#10
I just clean my tires with Simple Green, works well.
#11
Originally posted by BigDogRacing
If you let them sit with compound on them (in the heat), you will have one greasy, skating, donut cutting ride! lol
If you let them sit with compound on them (in the heat), you will have one greasy, skating, donut cutting ride! lol
#12
Tech Adept
Trips,
You are absolutley right about the Teac it is what used to be the traction compound to have way back when things were just getting going. As I recall it was banned by most Race Directors not just because of its smell but because in the quantities that RC drivers were using it it was toxic. Its not a problem if all you are doing is using a Q Tip to put a little on a pinch wheel on a tape deck but if you are treating tires several times a meeting then its a problem.
You are absolutley right about the Teac it is what used to be the traction compound to have way back when things were just getting going. As I recall it was banned by most Race Directors not just because of its smell but because in the quantities that RC drivers were using it it was toxic. Its not a problem if all you are doing is using a Q Tip to put a little on a pinch wheel on a tape deck but if you are treating tires several times a meeting then its a problem.
#13
Tech Elite
iTrader: (16)
I agreee. In fact, calling it "toxic" might not be a strong enough caution. A better description might be "this stuff will eat your soul and leave you in a puddle under the workbench". I remember back in the early 1/12 scale days, when you had a room full of folks using this stuff, after the races the parking lot looked like a scene from "Night of the Living Dead", a bunch of RC Zombies staggering around.
It's also pretty nasty around some plastics... I wouldn't be surprised if it could melt through a graphite tub chassis if it got on there by mistake.
Trips
It's also pretty nasty around some plastics... I wouldn't be surprised if it could melt through a graphite tub chassis if it got on there by mistake.
Trips
#15
Okay, so what are the track directors using to spray on to the track surface? Especially concrete. We are currently using cheap strawberry pop, but I am wondering if there is something easier or better to use. I just clean the tires with slightly diluted simple green. Makes the tires slightly tacky.
E
E