Reflex Suspension Dynamics (RSD) TC6 Upgrades (vertical ball studs, pistons,etc)

You're on Page 157 of 197
Go to
  • All chassis pre-orders have shipped.
  • Quote: All chassis pre-orders have shipped.
    Woohoo!

    Looking forward to rebuilding my car with the new chassis!
  • Quote: All the chassis are now in stock, all pre-orders will start shipping tomorrow and ship out by Friday.

    If you have been waiting on ordering one, you better hurry up, we only have a few left out of the first batch. :\

    On another note, our lowered, captured lay shafts holders will arrive in about 2 weeks. They will be anodized in Orange.

    Also in that same production batch, we will have a re-stock of the asphalt springs, (which will replace the Purple Spring with an in between rate that will lie between the silver/green and red), the 4 Hole Pistons in every flavor and a new carpet spring rate, softer than the black. blah blah blah


    This week we are also starting the development of some 12th scale option parts. We will focus on general use items at first, which will include high quality springs, (side, center, front) hardware and bearings.
    NICE !
  • RX4
    Hey guys,

    Christian and I have had a couple days to work together on finding a good mod setup for the RX4. My local track is 80x36 and we currently have the Vegas layout down, the best that we can considering the size of our track. This setup may be a little aggressive for a larger, more open track but it works well on a tight layout.

    Setup here: http://forum.teamxray.com/xform/inde...D=522&setup=t4

    Hope you guys find it to be a good starting point when you build yours!

    Robbie
  • Quote: Hey guys,

    Christian and I have had a couple days to work together on finding a good mod setup for the RX4. My local track is 80x36 and we currently have the Vegas layout down, the best that we can considering the size of our track. This setup may be a little aggressive for a larger, more open track but it works well on a tight layout.

    Setup here: http://forum.teamxray.com/xform/inde...D=522&setup=t4

    Hope you guys find it to be a good starting point when you build yours!

    Robbie
    Sweet, thanks guys.
  • Hey CT, ygpm 2 of them
  • Please use the store email with store related concerns. Otherwise it is very hard to keep track of all inquiries. Use the PMs, for "Personal" Matters when possible. I am terrible at responding PMs, Facebook messages, and Texts. Emails however are much easier and they leave a trail.

    I will try to remember tomorrow, but if you can, just drop a line @ [email protected]
  • New Items and RX4 Replacement Parts

    RX4-02 Rear Hinge Pins for RX4


    RX4-03 Front Hinge Pins for RX4


    RX4-04 Suspension Pivot Balls (8 Pcs)


    RX4-05 Suspension Mount Inserts


    and 12th Scale Miscellaneous


    RSD1201 Rear Axle Flanged Bearings


    RSD1202 Front 1/8 Axle Flanged Bearings


    RSD1203 1/8 Carbide Diff Balls


    RSD1204 8/32 Nylon hex Nuts
  • Myron, got you taken care of.

    Thanks.
  • Quote: Myron, got you taken care of.

    Thanks.
    thx...also you might have answered this...the blocks for the TC6..do you still carry those...Im using the screws, but they still back out from time.

    Thx again
  • Unfortunately, we do not make the block locks any longer.
  • Just sent an order your way Cristian. Thanks for the support!

    EA
  • Rx4
    So on the rx4 conversion do you adjust roll center by using shims under suspension mounts? Is so do the spec r r1 shims work or do you have a set that you sell.thanks
  • The Spec R shims will work. We will have some of our own as well soon.
  • Thanks