Originally Posted by gashuffer
(Post 9738853)
Does the Hara Twister 2.2 have li-po cut off?
It do have 6.0V cut-off setting. But before it cut you probably can feel the slowing down of your car, for me at that moment the battery about 6.5~6.6V. |
Twister 2.0
Dear all, i have a Twister 2.0 which is intalled on my old trust worthy HPI Pro 4 which i am converting for drift.
Would really love to run Lipo, is it possible and how about the Lipo auto cutoff can the ESC be updated? Thanks |
Originally Posted by speed6
(Post 11324290)
Dear all, i have a Twister 2.0 which is intalled on my old trust worthy HPI Pro 4 which i am converting for drift.
Would really love to run Lipo, is it possible and how about the Lipo auto cutoff can the ESC be updated? Thanks Make your life easy...pick up one of the Novak Smart-Stop units. Now they're even better than before because they're good one- to four-cell with auto-detect where before you had to buy a two-cell unit or a three cell unit specifically. Reasonably priced and pretty dead-nuts reliable. |
Capacitors Needed?
I have two of these ESCs(KO Propo VFS-1 item # 40051).
-Does anyone know if Capacitors are needed to be installed on this ESC? Thank You |
Originally Posted by GuyIsDamGood
(Post 15126661)
I have two of these ESCs(KO Propo VFS-1 item # 40051).
-Does anyone know if Capacitors are needed to be installed on this ESC? Thank You It has been a longtime since I ran those, but I believe I did run Caps on them, but I am not 100% sure you may want to contact Ko |
Originally Posted by GuyIsDamGood
(Post 15126661)
I have two of these ESCs(KO Propo VFS-1 item # 40051).
-Does anyone know if Capacitors are needed to be installed on this ESC? Thank You http://cdn.rcmart.com/images/ko_40045_002.jpg you can see the stock one on the left (and the schottky diode on the right) |
KO PROPO VFS-1 Brushless ESC
Thanks for the info Big B and cplus.
I should've mentioned that the KO Propo VFS-1 (item # 40051) in question for Capacitors; is the Brushless ESC. Thank You |
Originally Posted by GuyIsDamGood
(Post 15126736)
Thanks for the info Big B and cplus.
I should've mentioned that the KO Propo VFS-1 (item # 40051) in question for Capacitors; is the Brushless ESC. Thank You |
Originally Posted by GuyIsDamGood
(Post 15126736)
Thanks for the info Big B and cplus.
I should've mentioned that the KO Propo VFS-1 (item # 40051) in question for Capacitors; is the Brushless ESC. Thank You |
Thanks for the info Johnny Wishbone and cplus.
(Johnny Wishbone. Do you run Capacitors on your ESC?) I believe the latest VFS-1 (item # 40052) comes with Capacitors. - so it's safe to say Capacitors will improve the performance of the older VFS-1 ESC (item # 40051). I will install the capacitors and try it. |
Does anyone know what is the stock Cut-Off Voltage setting on the ESC?
-Ni-MH or Li-Po? Thank You |
NiMH, clearly. so it will kill your LiPO...
|
Originally Posted by Airwave
(Post 15216209)
NiMH, clearly. so it will kill your LiPO...
Thanks for the info; Airwave. I have to change the Cut-Off Voltage to prevent damage to my Li-Po battery. -the only way to change the Cut-Off Voltage is through a computer? -or; is there another way to do the changes? Thank You |
All times are GMT -7. It is currently 12:31 AM. |
Powered By: vBulletin v3.9.3.8
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.