LRP SXX StockSpec V2 ESC
06-22-2013, 05:44 PM
#1157
Tech Apprentice
newbie question
Hi.
What settings do I start with for 1/12th using 13.5t BL motor? I have a LRP SXX Competition v2. I run in a large indoor asphalt track.
Thanks.
What settings do I start with for 1/12th using 13.5t BL motor? I have a LRP SXX Competition v2. I run in a large indoor asphalt track.
Thanks.
06-24-2013, 10:27 AM
#1158
Quick question for all the braniacs out their. Just picked up a SXX V2 (Actually a Nosram Pearl Evo V2) which was repaired by the distributor with the upgrade logic board being fitted. The esc sets up fine, stores all settings on 2S but when I connect it to a 1S Lipo the orange light comes on and the motor turns at a slow speed. This is after turning off the lipo protection when the 2S was still attached. As their is no mention of orange light only on the troubleshooting guide could someone point out the problem?
Tried setting it up on 1S only, it apparently establishes the endpoints but after the setup is complete their is nothing, enter the mode setup and switch off the voltage cut off and still nothing.
Tried setting it up on 1S only, it apparently establishes the endpoints but after the setup is complete their is nothing, enter the mode setup and switch off the voltage cut off and still nothing.
06-24-2013, 02:22 PM
#1159
Quick question for all the braniacs out their. Just picked up a SXX V2 (Actually a Nosram Pearl Evo V2) which was repaired by the distributor with the upgrade logic board being fitted. The esc sets up fine, stores all settings on 2S but when I connect it to a 1S Lipo the orange light comes on and the motor turns at a slow speed. This is after turning off the lipo protection when the 2S was still attached. As their is no mention of orange light only on the troubleshooting guide could someone point out the problem?
Tried setting it up on 1S only, it apparently establishes the endpoints but after the setup is complete their is nothing, enter the mode setup and switch off the voltage cut off and still nothing.
Tried setting it up on 1S only, it apparently establishes the endpoints but after the setup is complete their is nothing, enter the mode setup and switch off the voltage cut off and still nothing.
06-25-2013, 05:55 AM
#1160
Thanks for the clarification.
07-27-2013, 08:00 PM
#1161
Blinky mode
So I bought a used LRP SXX version 2 and it seems to work fine we were running open ESC and it was great. but have changed over to run the class in Blinky mode and here is where I'm having issues.
When in Mode 2 "torque feel" it needs to be at 0 to be blinky and it skips right over the 0 setting? Goes from setting 10 to 1
I tried resetting the ESC binding it to my radio and it started blinking but it also reset the lipo mode to 2S and once I set the lipo mode back to 1S it quit blinking and won't go to 0 on mode 2
Any ideas?
When in Mode 2 "torque feel" it needs to be at 0 to be blinky and it skips right over the 0 setting? Goes from setting 10 to 1
I tried resetting the ESC binding it to my radio and it started blinking but it also reset the lipo mode to 2S and once I set the lipo mode back to 1S it quit blinking and won't go to 0 on mode 2
Any ideas?
07-27-2013, 08:21 PM
#1162
So I bought a used LRP SXX version 2 and it seems to work fine we were running open ESC and it was great. but have changed over to run the class in Blinky mode and here is where I'm having issues.
When in Mode 2 "torque feel" it needs to be at 0 to be blinky and it skips right over the 0 setting? Goes from setting 10 to 1
I tried resetting the ESC binding it to my radio and it started blinking but it also reset the lipo mode to 2S and once I set the lipo mode back to 1S it quit blinking and won't go to 0 on mode 2
Any ideas?
When in Mode 2 "torque feel" it needs to be at 0 to be blinky and it skips right over the 0 setting? Goes from setting 10 to 1
I tried resetting the ESC binding it to my radio and it started blinking but it also reset the lipo mode to 2S and once I set the lipo mode back to 1S it quit blinking and won't go to 0 on mode 2
Any ideas?
0-1-0-X
07-27-2013, 08:42 PM
#1163
LRP
The paper I have shows a 0 setting for torque feel.
http://www.teamassociated.com/pdf/di...e_lrp80915.pdf
http://www.teamassociated.com/pdf/di...e_lrp80915.pdf
07-27-2013, 09:06 PM
#1165
Blink
How can you get it to blink when torque feel is advanced? Or are you saying I can show tech that Boost is at 0 and they will consider that blinky?
07-28-2013, 09:36 AM
#1167
Firmware
Is there a firmware update or something I could download?
07-28-2013, 01:38 PM
#1168
modes 2 and 3 need to be at zero (default) to get the blue light to blink
