Robitronic Dyno Software Reg HELP!!
#1
Robitronic Dyno Software Reg HELP!!
I'm hoping someone can offer some help.
Installed the ProMaster II Windows software on XP. Went to register and the page the software links to is dead!!
Anyone else have any ideas? I emailed them (twice) got nothing.
HELP!!
Thanks in advance all!
Installed the ProMaster II Windows software on XP. Went to register and the page the software links to is dead!!
Anyone else have any ideas? I emailed them (twice) got nothing.
HELP!!
Thanks in advance all!
#3
#4
thx
Thx for the contact email Tre, we'll see what happens. Maybe its some sort of holiday in Austria??
Turbo Dyno? Didn't have a grand laying around to spend.... not a bad piece of gear but you have to CONSTANTLY maintain the slave motor. Also, those 60amp power supplies are expensive and fun to carry around...
Turbo Dyno? Didn't have a grand laying around to spend.... not a bad piece of gear but you have to CONSTANTLY maintain the slave motor. Also, those 60amp power supplies are expensive and fun to carry around...
#5
Tech Master
iTrader: (1)
I know this doesn't apply to what you have, but since it was mentioned ........a turbo dyno 45 only needs a pretty small size 45 amp power supply, or even a smaller 30amp supply if you only do stock or 19 turns like many people........also Iv'e never seen a need to rebuild the slave motor any sooner than dynoing 100 plus motors or more..(unless you do all mods)....Thats a pretty long time without "any" changes in readings
#7
Super Moderator
iTrader: (2)
I'm not too sure what's going on there either, haven't even been able to go to their site lately(though I'm no longer gonna worry about using the Windows version of the software, I think I prefer the old program, especially since I can easily go back to any previous runs whether I saved them or not, & the fact that I don't have to purchase that one).......
#9
Uh oh...
www.robitronic.com is GONE!
WTF?? Don't tell me..... they're out of business???
Nice........
How bout this?
Anyone able to run the DOS version on XP? I tried (and so did 2 other VERY knowledgeable guys) to get it to work and NO go.
Again, thanks for the help!
WTF?? Don't tell me..... they're out of business???
Nice........
How bout this?
Anyone able to run the DOS version on XP? I tried (and so did 2 other VERY knowledgeable guys) to get it to work and NO go.
Again, thanks for the help!
#10
i doubt they are out of business, they just came out with a new speed control.
maybe website change???
maybe website change???
#11
Super Moderator
iTrader: (2)
Originally Posted by FreqETag
www.robitronic.com is GONE!
WTF?? Don't tell me..... they're out of business???
Nice........
How bout this?
Anyone able to run the DOS version on XP? I tried (and so did 2 other VERY knowledgeable guys) to get it to work and NO go.
Again, thanks for the help!
WTF?? Don't tell me..... they're out of business???
Nice........
How bout this?
Anyone able to run the DOS version on XP? I tried (and so did 2 other VERY knowledgeable guys) to get it to work and NO go.
Again, thanks for the help!
#12
Tech Adept
Looks like they have a new web site, but I haven't looked at their site for A LONG time...
I've never owned the Promaster II software, however I did download it today, and it seems to work on my install of WinXP, but I have not registred it, so I'm only in 'lite' mode.
I've never owned the Promaster II software, however I did download it today, and it seems to work on my install of WinXP, but I have not registred it, so I'm only in 'lite' mode.
#14
robi software for xp
I am in the same boat. unfortunatly I have not had time to try mine out since I bought the dyno a few months ago.
Was the $60 for an xp version and if so could you let me know the new email/website because I might as well order a xp version myself.
I about got the car built so it is time to get to work on some motors and get back to racing.
Thanks for the help.
Darrald
Was the $60 for an xp version and if so could you let me know the new email/website because I might as well order a xp version myself.
I about got the car built so it is time to get to work on some motors and get back to racing.
Thanks for the help.
Darrald
#15
robi xp software
did anyone try running it in the compatibility mode of xp?
I am by no means a computer whiz. I asked one of the IT guys here at work. All he could say was "it might work" if you pick manual in the compatibility wizard and let it walk you through it.
I will try it tonight.
I am by no means a computer whiz. I asked one of the IT guys here at work. All he could say was "it might work" if you pick manual in the compatibility wizard and let it walk you through it.
I will try it tonight.