Losi XXX-S
09-08-2001, 06:04 PM
#331
shuie..that is what i did....just screw it to the diff cover...it works fine...
09-09-2001, 08:14 AM
#337
Tech Initiate
SirSpeedy, do u have the rest of the new MF part# and can u post them?
09-09-2001, 05:20 PM
#339
TY - All you need to do is stiffen it up. Check ou the losi site and start with the carpet setup. It's pretty good. as compared to the TC3..let's just say you will be very impressed.
09-09-2001, 06:41 PM
#341
Tech Fanatic
iTrader: (49)
A little update on the Aluminum CVDs.
If you break the front suspension, you WILL tear up the Aluminum dogbone.
The place where it breaks is where the pin goes through the bone and the axle. I hit a board today and broke a steering hub and this is when the cvd bone got messed up.
Now, granted, I shouldn't of hit the board but things happen.
BTW, this is the first time I have broken any pieces on the car.
If you break the front suspension, you WILL tear up the Aluminum dogbone.
The place where it breaks is where the pin goes through the bone and the axle. I hit a board today and broke a steering hub and this is when the cvd bone got messed up.
Now, granted, I shouldn't of hit the board but things happen.
BTW, this is the first time I have broken any pieces on the car.
09-09-2001, 07:38 PM
#343
I have the whole list in front of me right now. Put "TMF" in front of all the PN's for the full PN.
1100 - Red foam bumper
1101 graphite bumper brace
1102 Heatsink Battery hold-down
1103 Battery hold-down posts (2)
1104 Al motor clamp
1105 - Sus A-arm mounts, 0/4 & 2
1107 Front Sus. Arm rear mounts L & R
1108 Rear Sus arm mounts 0/4 & 2
1110 Rear usupension arm front mounts L & R
1111 motor heatsink
1112 Servo mounts
1113 steering brace
1114 Wheel adaptors ( std hex ) 4
1115 Rear carriers, 2
1116 Shock bushings
1117 Gear adaptor
1118 Frnt spindles
1119 steering bellcranks
1120 motor mount
That took a long time to type.. lol
1100 - Red foam bumper
1101 graphite bumper brace
1102 Heatsink Battery hold-down
1103 Battery hold-down posts (2)
1104 Al motor clamp
1105 - Sus A-arm mounts, 0/4 & 2
1107 Front Sus. Arm rear mounts L & R
1108 Rear Sus arm mounts 0/4 & 2
1110 Rear usupension arm front mounts L & R
1111 motor heatsink
1112 Servo mounts
1113 steering brace
1114 Wheel adaptors ( std hex ) 4
1115 Rear carriers, 2
1116 Shock bushings
1117 Gear adaptor
1118 Frnt spindles
1119 steering bellcranks
1120 motor mount
That took a long time to type.. lol
09-09-2001, 08:09 PM
#344
Tech Adept
Originally posted by Schuie Driver
Ty - The car is absolutely fantastic on carpet. No problems in keeping up with the TC3's. Check out my earlier posts for a good stock sedan set up with foams.
Ty - The car is absolutely fantastic on carpet. No problems in keeping up with the TC3's. Check out my earlier posts for a good stock sedan set up with foams.
I ran the xxx-s in a race today........ it was slow even geared the same as my TC3...........
I was able to run faster lap times with my TC3, then with the XXX-S......
I am not saying that the XXX-s was slow, I was right with the front 2 guys all thru the race..........
09-09-2001, 08:15 PM
#345
troy...that was why i did not put all the info in...i heald back...
wolverine....what setup did you have in the xxx-s????cause it should be just as fast as a tc3, iif not better...
wolverine....what setup did you have in the xxx-s????cause it should be just as fast as a tc3, iif not better...
