Losi XXX-S

Old 08-28-2001, 10:06 AM
  #151  
Tech Apprentice
 
Join Date: Aug 2001
Location: MD
Posts: 74
Default

hmmmm thanx I always wondered what that was for ....j/k
holy ear guy is offline  
Old 08-28-2001, 10:07 AM
  #152  
Tech Elite
 
mike_Webb's Avatar
 
Join Date: Aug 2001
Location: SOMEWHERE OVER THE RAINBOW
Posts: 3,128
Default

I got installed the Blue aluminum Lower Center of Gravity motor mount for the XX4 and SW and that does a good job of allowing the motor to cool down. A heatsink would be a good combo to add to that.
mike_Webb is offline  
Old 08-28-2001, 10:08 AM
  #153  
Tech Elite
iTrader: (26)
 
Join Date: Aug 2001
Location: Los Angeles, CA
Posts: 4,150
Trader Rating: 26 (100%+)
Default

Yep, that is it.

Works alot better than the clip on heatsinks.
MDawson is offline  
Old 08-28-2001, 10:09 AM
  #154  
RCTech Member #2
Thread Starter
iTrader: (5)
 
TSR6's Avatar
 
Join Date: Aug 2001
Posts: 5,961
Trader Rating: 5 (100%+)
Default

Originally posted by mike_Webb
I got installed the Blue aluminum Lower Center of Gravity motor mount for the XX4 and SW
I have no idea what that is.. lol

I'll look into it ,Thanks.
TSR6 is offline  
Old 08-28-2001, 10:13 AM
  #155  
Tech Elite
 
mike_Webb's Avatar
 
Join Date: Aug 2001
Location: SOMEWHERE OVER THE RAINBOW
Posts: 3,128
Default

Troy-

TK3068 Blue Aluminum Lowered Motor Mount Heat Sink $14.99

From Trinity

Mike Webb
mike_Webb is offline  
Old 08-28-2001, 10:28 AM
  #156  
RCTech Member #2
Thread Starter
iTrader: (5)
 
TSR6's Avatar
 
Join Date: Aug 2001
Posts: 5,961
Trader Rating: 5 (100%+)
Default

Ok Thanks! I'll add that on my list of stuff to get.

Gotta sell my Pro2 before i can get anymore RC stuff lol
TSR6 is offline  
Old 08-28-2001, 11:09 AM
  #157  
Tech Elite
 
mike_Webb's Avatar
 
Join Date: Aug 2001
Location: SOMEWHERE OVER THE RAINBOW
Posts: 3,128
Default

Troy-

I should add that the 3mmx6mm Motor Screws will not fit. I had to go buy 3mmx8mm Motor Screws so that it fits properly
mike_Webb is offline  
Old 08-28-2001, 11:10 AM
  #158  
Administrator
iTrader: (26)
 
Matt M.'s Avatar
 
Join Date: Aug 2001
Posts: 8,549
Trader Rating: 26 (100%+)
Default

mark i see you also owned a ft tc3....by the lexan trans mount and the transpponder
Matt M. is offline  
Old 08-28-2001, 11:12 AM
  #159  
RCTech Member #2
Thread Starter
iTrader: (5)
 
TSR6's Avatar
 
Join Date: Aug 2001
Posts: 5,961
Trader Rating: 5 (100%+)
Default

matt - prolly ...lol.. but you can get the mount seperate. I think we accually have the lexan mount at my lhs... we did at one point anyways. I almost got it when i built my XXX-S.. but i made my own. Yours looks kinda cool though..
TSR6 is offline  
Old 08-28-2001, 11:38 AM
  #160  
Tech Elite
 
mike_Webb's Avatar
 
Join Date: Aug 2001
Location: SOMEWHERE OVER THE RAINBOW
Posts: 3,128
Default

Just got my Quantum and all I got to say is wow....it is small and nice. can't wait to see my Computer tonight so I can buy 6 packs of 3000 SMH and slap my TI 8 turn Single in t .
mike_Webb is offline  
Old 08-28-2001, 12:46 PM
  #161  
Administrator
iTrader: (26)
 
Matt M.'s Avatar
 
Join Date: Aug 2001
Posts: 8,549
Trader Rating: 26 (100%+)
Default

mine is froma mugen.....i dant know wich though
Matt M. is offline  
Old 08-28-2001, 02:05 PM
  #162  
Tech Apprentice
 
Join Date: Aug 2001
Location: MD
Posts: 74
Default

do you actually slide the motor into the (street weapon) heatsink?
holy ear guy is offline  
Old 08-28-2001, 02:22 PM
  #163  
Tech Elite
 
mike_Webb's Avatar
 
Join Date: Aug 2001
Location: SOMEWHERE OVER THE RAINBOW
Posts: 3,128
Default

no..it is just like the XXX-S motor plate. same cutout and holes. it just has a 2mm gap beteween the front of the plate and the motor for air to get in front of the motor and there are 3 aluminum strips that comeout to support the motor and allow it to cool by dispating heat. It is not really needed but a guy at my track was running it with is Motor and says it helps with cooling. He also had the XX4\SW Outdrive Covers and the Shock aluminum supports and some other parts for the XX4\SW.

Mike Webb
mike_Webb is offline  
Old 08-28-2001, 02:23 PM
  #164  
Tech Elite
iTrader: (26)
 
Join Date: Aug 2001
Location: Los Angeles, CA
Posts: 4,150
Trader Rating: 26 (100%+)
Default

Originally posted by mr. losi
mark i see you also owned a ft tc3....by the lexan trans mount and the transpponder
Yep, I retired the TC3 a long time ago. I did like the transponder mount well enough to use it on this car
MDawson is offline  
Old 08-28-2001, 02:27 PM
  #165  
Tech Elite
iTrader: (26)
 
Join Date: Aug 2001
Location: Los Angeles, CA
Posts: 4,150
Trader Rating: 26 (100%+)
Default

Originally posted by holy ear guy
do you actually slide the motor into the (street weapon) heatsink?
For the heatsink that I have pictured, yes the motor does slide into the heatsink .
MDawson is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.