Hot Bodies TCX
#1067
my blog in the sig below has been updated with the set up that i ran during the weekend, 99% is the same as ive been running everywhere on carpet, mainly just playing with additive times to find the right balance of the car for the whole run.
hth
luke
hth
luke
#1068
Tech Adept
So at 490-415$
Is this car the middle of the road, or higher end of cost?
Was this a raised price compared to the cyclone??
Looking at this one and the Associated T6....
what was the T5 like??
Thanks.
Is this car the middle of the road, or higher end of cost?
Was this a raised price compared to the cyclone??
Looking at this one and the Associated T6....
what was the T5 like??
Thanks.
#1069
Tech Adept
Is it me, or does the Xray T3 look like the TCX, or the TCX look like the Xray
T3??
It has a upper deck the same as the TX3...?? You can adjust the flex the same way???
T3??
It has a upper deck the same as the TX3...?? You can adjust the flex the same way???
#1070
Tech Champion
iTrader: (32)
yesterday at the castle classic at nor-cal, i broke both of the front dogbones on my tcx. a buddy gave me 2 complete dogbones/axles to try from his T.O.P. car. i used my dremel to narrow the plastic blades a bit, but it was a perfect fit,,,,46mm, and the best part, they are steel dogbones.
#1071
Tech Addict
hey, you know me, i can break anything..lol....the dogbones are 46mm long, the tamiya ones are only 44mm,,,the TOP dogbones worked great, but i did have to dremel down the blades to make it fit,,,lucky there is a lot of material on the blades
#1073
Tech Addict
#1074
yesterday i had a chance to try my NEW tcx in my club race, it was 17.5 WITHOUT boost and the dog bones are starting to showing signs of wear.
which dog bones that will last longer and fit tcx?
which dog bones that will last longer and fit tcx?
#1076
I had a dogbone "redesigned" too last last week-end...
I obviously try the Tamiya but the kingpin are too small to fit the spool...
I've ordered some Sakura parts to adapt the gear diff... Maybe it could be a perfect replacement for our dogbones... And if it does not fit, maybe I can try to adapt the outdrives or the totality of the Sakura spool...
I obviously try the Tamiya but the kingpin are too small to fit the spool...
I've ordered some Sakura parts to adapt the gear diff... Maybe it could be a perfect replacement for our dogbones... And if it does not fit, maybe I can try to adapt the outdrives or the totality of the Sakura spool...
#1077
why would tcx make their aluminum axles so weak and not offering stronger option front axles for tcx?? does every tcx owner have to modify other manufacturers axles?
Last edited by littlealex; 10-12-2010 at 10:16 AM.
#1078
Where are your bones wearing? Can you post a picture up?
With 17.5 zero boost you shouldn't have ANY wear problems pretty much ever.
I've been running mod and 10.5 (with boost) for about 40 runs so far with no wear or broken bones....
What type of grease and anti wear grease are you using?
With 17.5 zero boost you shouldn't have ANY wear problems pretty much ever.
I've been running mod and 10.5 (with boost) for about 40 runs so far with no wear or broken bones....
What type of grease and anti wear grease are you using?
#1079
Where are your bones wearing? Can you post a picture up?
With 17.5 zero boost you shouldn't have ANY wear problems pretty much ever.
I've been running mod and 10.5 (with boost) for about 40 runs so far with no wear or broken bones....
What type of grease and anti wear grease are you using?
With 17.5 zero boost you shouldn't have ANY wear problems pretty much ever.
I've been running mod and 10.5 (with boost) for about 40 runs so far with no wear or broken bones....
What type of grease and anti wear grease are you using?
I am running 13.5T
Hopefully steel 46mm bones will be available soon, at £9 each for the alu ones it is expensive!
I am think of trying the TC 44mm steel versions - as long as they don't pop out
#1080
Yes, stock 46mm shafts are showing extreme wear. After two weeks of running at Horsham, the axle end of the shaft is already egg'ed out. I run 17.5T Open.
Does anyone know if the Sakura 46mm shaft a direct fit?
Does anyone know if the Sakura 46mm shaft a direct fit?