XERUN V2.0 Brushless ESC discussion thread.
#886
Hi all
Can anyone tell me which firmware the speedo has out of the box?
Does it include the 'supercharge' profile and will it hang with the Tekins and GMs .... or will I need to update via the LCD box.
Also .. where do you find the firmware updates? I had a look at the HW site and there doesnt appear to be anything of note on there.
Pip
Can anyone tell me which firmware the speedo has out of the box?
Does it include the 'supercharge' profile and will it hang with the Tekins and GMs .... or will I need to update via the LCD box.
Also .. where do you find the firmware updates? I had a look at the HW site and there doesnt appear to be anything of note on there.
Pip
#887
Hi all
Can anyone tell me which firmware the speedo has out of the box?
Does it include the 'supercharge' profile and will it hang with the Tekins and GMs .... or will I need to update via the LCD box.
Also .. where do you find the firmware updates? I had a look at the HW site and there doesnt appear to be anything of note on there.
Pip
Can anyone tell me which firmware the speedo has out of the box?
Does it include the 'supercharge' profile and will it hang with the Tekins and GMs .... or will I need to update via the LCD box.
Also .. where do you find the firmware updates? I had a look at the HW site and there doesnt appear to be anything of note on there.
Pip
A friend of mine bought a new XErun 60A V2 a few days ago and I checked it and it had 323t installed. We promptly installed the 522 (he doesn't have a professional LCD yet).
If that's an indication...
#889
Thanks guys .
To be more specific ..
Does anyone know which firmware is on the 120a Blue Spirit?
To be more specific ..
Does anyone know which firmware is on the 120a Blue Spirit?
#890
need help!!
Hey Guys,
I just installed my XERun 80A into my 2wd slash and had problems
I'm running a 2 cell lipo and a 10.5 motor.
I tried setting the ESC with min. timing and the motor had 0* with a 25-86 gear ratio.
No matter how I changed my settings, when I pulled the throttle the slash would act as if it's loosing radio power and loose stearing and coast to a stop. I tried different recievers and motors, but no luck.
The last settings I tried were:
Forward with break
0% drag break
3.0v/cell low voltage
level 1 punch
25% break force
25% reverse force
0% initial break force
1 timing
6% neutral width
enabled over-heat protection
CCW rotation
auto calc lipo cells
Any suggestions??
Thanks in advance!!
I just installed my XERun 80A into my 2wd slash and had problems
I'm running a 2 cell lipo and a 10.5 motor.
I tried setting the ESC with min. timing and the motor had 0* with a 25-86 gear ratio.
No matter how I changed my settings, when I pulled the throttle the slash would act as if it's loosing radio power and loose stearing and coast to a stop. I tried different recievers and motors, but no luck.
The last settings I tried were:
Forward with break
0% drag break
3.0v/cell low voltage
level 1 punch
25% break force
25% reverse force
0% initial break force
1 timing
6% neutral width
enabled over-heat protection
CCW rotation
auto calc lipo cells
Any suggestions??
Thanks in advance!!
#891
Tech Adept
Hobbywing esc
Hi All
What HW model is excelent for 13.5 ?
What HW model is excelent for 13.5 ?
#892
Sorry for this! I also saw there was the 422, and I mixed it up when I wrote the above answer!
#893
the thanks i get for updating your speedo. its too fast! i like it. try settings 4,9 and 15. 4 and 9 lower number and 15 to a higher number. 15 on 6 should give you less out of the bends, 4 and 9 on a lower number to also soften the punch. come up to hrcc on a friday and we can have a little play. regards al.
#894
Tech Apprentice
Hi all
Can anyone tell me which firmware the speedo has out of the box?
Does it include the 'supercharge' profile and will it hang with the Tekins and GMs .... or will I need to update via the LCD box.
Also .. where do you find the firmware updates? I had a look at the HW site and there doesnt appear to be anything of note on there.
Pip
Can anyone tell me which firmware the speedo has out of the box?
Does it include the 'supercharge' profile and will it hang with the Tekins and GMs .... or will I need to update via the LCD box.
Also .. where do you find the firmware updates? I had a look at the HW site and there doesnt appear to be anything of note on there.
Pip
Instructions for the supercharger settings is the first download listed.
The last one listed is for the USB link and the firmware
I bought mine 6 months ago and I think it came with 323 and that was version #23 and now we have some 50 or so versions
Last edited by TBOTubed; 06-06-2010 at 04:03 AM.
#895
#896
Thanks TBOT..
I think I will have to invest and give it a go..
The download is not recognised by my pc. Do I need the LCD box and software to be installed before I can have a look at it?
I think I will have to invest and give it a go..
The download is not recognised by my pc. Do I need the LCD box and software to be installed before I can have a look at it?
#898
Tech Initiate
I'm currently running the EZRun 80A ESC with the bundled 3674SL brushless motor with 20c 5000MAH lipos....
-would I see any improvement in performance if I upgraded to the new XERun 80a ESC brushless combos?
-or would performance differences be minimal and I should just keep using the EZRun 80A Brushless kit?
Thanks
-would I see any improvement in performance if I upgraded to the new XERun 80a ESC brushless combos?
-or would performance differences be minimal and I should just keep using the EZRun 80A Brushless kit?
Thanks
#900
Tech Apprentice
yep , thats the idea. The newest HW lists 4 or 5 of the newest firmwares to choose from. An older "beta" SP or HW file would have all the ones leading up to the current files but I dont see why you would want those.The current ones are very refined.