R/C Tech Forums - The Speed Passion Thread

Page 4 of 896

« First

104

504

Last »

Show 40 post(s) from this thread on one page

R/C Tech Forums (https://www.rctech.net/forum/)

- Electric On-Road (https://www.rctech.net/forum/electric-road-2/)

- - The Speed Passion Thread (https://www.rctech.net/forum/electric-road/288105-speed-passion-thread.html)

luic	04-13-2009 02:21 PM

Thanks Shawn, the next weekend tested it.
The last week, i classified 2nd and finish 1st in final A, with SP motor.
With this suggestions, and litle good luck, i hope repeat , ;):):nod:

Greetings, Luis C.

flatspunout

04-13-2009 02:41 PM

I just noticed that my 13.5 has zero endplay...is this the recommended tolerance or should there be .5-1mm like a brushed motor? Thanks!

-rocky b

abailey21

04-13-2009 03:00 PM

Tork=Torque:sneaky::sneaky:

And you call yourself a National Champion

Quote:

Originally Posted by Mike Haynes (Post 5679077)

Hey Tim the sp 10.5 will need a bit more pinion then the novak to feel comparable, it is a more tork based motor. Try gearing it up a few teeth but watch the temp, also the sp motors run well with a lot of esc timing.

tim fry

04-13-2009 03:10 PM

Quote:

Originally Posted by Shawn Palmer (Post 5679468)

Tim:
Yes, you'll need to be geared up a few teeth from where you had the Novak.

Thanks Shawn.

I'm at 5.4 now so your saying 5.2 or lower?

charlie_b

04-13-2009 03:23 PM

Shawn, this is what caused the broken case. Cheers.
http://i116.photobucket.com/albums/o...9584989649.jpg

I guess Speed Racer couldn't save Racer X on this one.

flatspunout

04-13-2009 03:27 PM

Quote:

Originally Posted by charlie_b (Post 5679745)

Shawn, this is what caused the broken case. Cheers.
http://i116.photobucket.com/albums/o...9584989649.jpg

I guess Speed Racer couldn't save Racer X on this one.

And he walked away...

-rocky b

Shawn Palmer

04-13-2009 03:39 PM

OW Charlie!

That reminds me of those "amazing X-ray" emails with the nails and fence posts through people's skulls!

I like the colors though - black and yellow rox!

Shawn Palmer

04-13-2009 03:40 PM

Tim - yes, 5.2-5.0 :)

Shawn Palmer

04-13-2009 03:41 PM

flatspun - yes, at least .5mm, and about 1mm max.

tmunno

04-13-2009 04:44 PM

Yahoo, When Charlie torture tests something he does it right!!!!!!!

Mike Haynes

04-13-2009 04:48 PM

Quote:

Originally Posted by abailey21 (Post 5679652)

Tork=Torque:sneaky::sneaky:

And you call yourself a National Champion

Um, my title happens to be for racing toy cars, not being "edumicated good at skule".

andrewdoherty

04-13-2009 05:06 PM

Quote:

Originally Posted by flatspunout (Post 5679757)

And he walked away...

-rocky b

Final Destination 17 - McSmooth's Revenge!

Trips

04-13-2009 05:07 PM

Why didn't Mike Haynes win the spelling b?

Because Mike Haynes is too fast to be in the B.

Yokomo_Ant3

04-13-2009 05:52 PM

Hey Guys, i am going to buy a SpeedPassion 2.0. Motor. I was going to get a 4.0. My question is do all of the motors have an inbuilt fan or are there some without? I have been told to get the one without the fan.:nod:

Also are the normal ones the same as the special edition motors. Eg the Mark R, Jilles edition etc.

If there are ones without the fan could i posssibly get a Pn?

Thanks

bigdadracing

04-13-2009 07:21 PM

[QUOTE=Shawn Palmer;5678929]Hi Russ:
Start with 98/34 and the timing advance maxxed out.

If you didn't run the timing maxxed in your 1.1, then take away another tooth per advance setting you are going up.

Keep your eye on motor temps every minute or so for the first few runs. If you follow the above, you'll be within a few teeth either way. (too hot - lose another tooth or two, or not quite fast enough add a
shawn , is that maxing out motor timming or the speedo's settings????

All times are GMT -7. It is currently 08:11 AM.

Page 4 of 896

Show 40 post(s) from this thread on one page