Originally Posted by Dlewis4 (Post 7048615)

anyone tell me what ESC this is and how to program it? I have been looking all over for instructions... but cant find any.

It is a Speed Passion... have the Programming card for it... but no instructions to get it setup with my radio.

Thanks guys...

Originally Posted by CraigM (Post 7048751)

Will SP be waiting on feedback from TITC racers before releasing the new software? Like everyone here I'm super keen to get my hands on it :D

Originally Posted by sammies (Post 7047354)

Ok... got myself a temp gun yesterday... at least now I know for sure how hot i'm running after 5minutes... will have to wait for friday for this bit of info...

I played around with timing yesterday... I was never interested in changing timing on the motor cause of temp issues... but out of curiosity last night, i maxed out timing on the motor with stock timing on the esc (110 software)... wow...WOW... the motor now screams at full throttle... this was a 'tabletop' test.

I think i will have a temp issue for sure this time... made 4 quick pulls bringing motor up gradually to full throttle, and the motor and esc was already warm... motor was registering 36 degrees and esc 40 degrees (celcius)... i know... still a long way to go... but this was a tabletop test though... if on the track with load and all... i just cant imagine... will have to take temp readings every 2 minutes just to be on the safe side.

Originally Posted by Stein Tumert (Post 7049157)

With the v3 13.5T SP motor and 110 software with timing on motor and ESC at max, the motor is only 52-54 degrees celcius after 5 min (FDR - 6.3)...

With the 107 sw it is another story with the temp...:sneaky:

...

Originally Posted by Solara (Post 7048800)

Firmware has to be approved by test drivers before it can be release. If they are not even being acceptable or there are bugs, SP will not release any of them.

We all see what TOYOTA did for themself. Ignoring the problem does not make the problem disappear.

I know I have the new firmware received and I just need the track time and send over date back to SP. And this set of firmware is the 6th revision/update after the 091110 software. Just so you know SP are working on newer software and did spend a lot of time and try to catch the "fast" one...and hope it will "PASS" them this time.

Originally Posted by Zooberg (Post 7049194)

hello. Can i use softwear 323 to drive mod 6.5 t speedpassion v.3 engine? Or can i use stock 110 or 107?

The new gt2.1 pro stock is it any limits on it? Can i use 6.5t engine on it?? Whats new in 2.1?

Originally Posted by abailey21 (Post 7048261)

Don't we all ;)



if it runs like a bad sensor, and you replaced everything BUT the sensor, more than likely you'll need a sensor.

Don't bother callig me at the shop we have no sensors and our last sales day was yesterday.
I'll keep an eye out for one for you

Originally Posted by Pica (Post 7049592)

Adam what recommendation would you give for a 3.5T speedp motor setup, in type of lipo's, gear ratio, (spur 84), super capacitor. Currently using the ESC GT2.0.
A complete setup for racing.

thx

Originally Posted by Zooberg (Post 7049194)

hello. Can i use softwear 323 to drive mod 6.5 t speedpassion v.3 engine? Or can i use stock 110 or 107?

The new gt2.1 pro stock is it any limits on it? Can i use 6.5t engine on it?? Whats new in 2.1?

Originally Posted by CraigM (Post 7048751)

Will SP be waiting on feedback from TITC racers before releasing the new software? Like everyone here I'm super keen to get my hands on it :D

Originally Posted by abailey21 (Post 7049626)

Drivers in the states already have been testing it. It should be ready soon.

Originally Posted by Me_MrTyson (Post 7049683)

Adam,

The update which is being tested, will that include some new Mod profiles or just a stock update??


Alex