T.O.P. Racing "Photon" 1/10 EP Touring Car
#2146
well i will try to give my set up
it started out as the stock rubber setup as a base line
went to 3deg total rear tow
-1 camber in rear
0 in front
324 springs in front
289 in rear
5min ride height
2.5 active droop (when tire lift off the ground)
front shocks top center hole
rear insecond to bottom
rear camber links are in the inside (at kit height)
widened the front by 3mm total
rear arms to moved to front
added 40g under front bumper
car weights in at 1477g
no let on chassis to balence it
i moved the batt out side of the chassis to balance it
it started out as the stock rubber setup as a base line
went to 3deg total rear tow
-1 camber in rear
0 in front
324 springs in front
289 in rear
5min ride height
2.5 active droop (when tire lift off the ground)
front shocks top center hole
rear insecond to bottom
rear camber links are in the inside (at kit height)
widened the front by 3mm total
rear arms to moved to front
added 40g under front bumper
car weights in at 1477g
no let on chassis to balence it
i moved the batt out side of the chassis to balance it
#2147
Tech Adept
Hi,
I just finished build up of my foam spec, but i noticed that the Jaco Prism rubs at the steering link at the steering hub?? anyone has the same problem? or do you guy's trim of the wheel so it fit's or just add spacers to make it fit? i am pretty new to foam tire racing.. any advise is helpful
I just finished build up of my foam spec, but i noticed that the Jaco Prism rubs at the steering link at the steering hub?? anyone has the same problem? or do you guy's trim of the wheel so it fit's or just add spacers to make it fit? i am pretty new to foam tire racing.. any advise is helpful
#2148
Hi,
I just finished build up of my foam spec, but i noticed that the Jaco Prism rubs at the steering link at the steering hub?? anyone has the same problem? or do you guy's trim of the wheel so it fit's or just add spacers to make it fit? i am pretty new to foam tire racing.. any advise is helpful
I just finished build up of my foam spec, but i noticed that the Jaco Prism rubs at the steering link at the steering hub?? anyone has the same problem? or do you guy's trim of the wheel so it fit's or just add spacers to make it fit? i am pretty new to foam tire racing.. any advise is helpful
#2150
#2151
good !
#2154
do they make an lipo carpet chassie for the car???
I hear they may not make the 6 degree blocks at all
I hear they may not make the 6 degree blocks at all
#2157
Tech Master
iTrader: (1)
I'm quite satisfied with the car. EJ and Juan were repeatedly doing 10.8s laps in 13.5t rubber, and I somehow managed that feat in round 3 of qualifying but never again. 10.8s is pretty much as fast as anyone went, including the eventual winner. I didn't break anything, and I finished every run I attempted - including all practices, qualifiers, and mains. I re-oiled two shocks.
I think we all had good setups, but our lack of high traction carpet experience kept us from really fine-tuning it. In my experience, the car has a very wide setup window in which it is good. That was very nice, because I was able to try changes and still have quality runs. I never had a crap run because I made the car undriveable or even challenging to drive.
Thanks again to EJ, Juan, and Michael for helping me with the car and a few other things, like tires and ESC settings.
Adam Glatt
I think we all had good setups, but our lack of high traction carpet experience kept us from really fine-tuning it. In my experience, the car has a very wide setup window in which it is good. That was very nice, because I was able to try changes and still have quality runs. I never had a crap run because I made the car undriveable or even challenging to drive.
Thanks again to EJ, Juan, and Michael for helping me with the car and a few other things, like tires and ESC settings.
Adam Glatt
#2158
Tech Apprentice
understeer
Hello guys,
I have been runnning the photon this weekend and the car was really good I nearly found a perfect set up, but during the heats the performance of the car came down after 3 minutes, the car understeer, some people told me that this is because I overheat the front tyres, is this true? how can I make the car more constant during the heat?
thank you in advance
I have been runnning the photon this weekend and the car was really good I nearly found a perfect set up, but during the heats the performance of the car came down after 3 minutes, the car understeer, some people told me that this is because I overheat the front tyres, is this true? how can I make the car more constant during the heat?
thank you in advance
#2159
Tech Elite
iTrader: (24)
Nitro Ho you are just a hater who has no idea what he is talking about. I asked you to send me your "brothers" setup and you never did.
First of all on foam tires the car def does not push with a good setup on it. Anyone who saw my car this weekend will agree push is not an issue
Secondly I believe we will be coming out with 6 degree blocks sometime in the future.
First of all on foam tires the car def does not push with a good setup on it. Anyone who saw my car this weekend will agree push is not an issue
Secondly I believe we will be coming out with 6 degree blocks sometime in the future.
#2160
hey there
does the arp stabilizer fit the photon.
where can i find a good setup for rubber carped .
i have a fairly good setup exept for the fast left and right cicanes.
there the back end gets a bit loose .
marcel pinkster
does the arp stabilizer fit the photon.
where can i find a good setup for rubber carped .
i have a fairly good setup exept for the fast left and right cicanes.
there the back end gets a bit loose .
marcel pinkster