Tamiya TRF415
front and rear are 15.5 but mine are longer to give maximum movement on the other arm
just set the fastest lap in stock practice tonight with my TRF415MSXX MRE !!!
19.440 lap , the new Xray009s were doing 19.670 and 19.840
YES GET IN !!!!!!
19.440 lap , the new Xray009s were doing 19.670 and 19.840
YES GET IN !!!!!!
Hi all
Just picked up a used MSXX and I'm looking for a base setup for carpet with rubber tyres and one for smooth medium grip tarmac. I have had a look on Eds site and not sure which ones I should pick.
Thanks
Just picked up a used MSXX and I'm looking for a base setup for carpet with rubber tyres and one for smooth medium grip tarmac. I have had a look on Eds site and not sure which ones I should pick.
Thanks
Tech Champion
iTrader: (32)
white front springs and 50WT oil
Blue rear springs and 35WT oil
25mm droop and 1.5 camber all round
front toe was 0 degrees
front sway bar only
using Vtec30's
droop is measured using the david junn meathod
and i'm faster then the new XrayT2 009
yep
I said it was a good setup our home tracks are similar , if you do the mods we spoke about you can take out 0.5 deg from your rear toe and no-one will catch ya down the straight HAVE IT
Go getum
Mark AUS
i really couldnt bring my self to cut the MRE
but foooooooook does it go around corners i stuffed it down the inside of 2 Xray009 drivers and a HPI cyclone TC
Hi
Looking to get back into tc racing, I picked a used 415msx of rctech. Where is the best place to go that summarize all that I need to know about this car. I'll be racing carpet foam w/ 13.5 brushless. And possilbly parking lot too. I use to race with a tc3 and I see that this is a different animal. All help will be appreciated.
Thanks
Looking to get back into tc racing, I picked a used 415msx of rctech. Where is the best place to go that summarize all that I need to know about this car. I'll be racing carpet foam w/ 13.5 brushless. And possilbly parking lot too. I use to race with a tc3 and I see that this is a different animal. All help will be appreciated.
Thanks
my servo saver seems to be sticky should i replace with a kimborough or just get another Tamiya one?
The tamiya ones are renowned for slop and poor fitting.
Sidecar phil, thanks, i'll see what I can do with mine
just looked in the MSXX book not the MSX and it say's 16mm not 15.5 like the early cars
just had my new DX3S stop working today !!!!!
just had my new DX3S stop working today !!!!!
Tech Champion
iTrader: (32)
Hi
Looking to get back into tc racing, I picked a used 415msx of rctech. Where is the best place to go that summarize all that I need to know about this car. I'll be racing carpet foam w/ 13.5 brushless. And possilbly parking lot too. I use to race with a tc3 and I see that this is a different animal. All help will be appreciated.
Thanks
Looking to get back into tc racing, I picked a used 415msx of rctech. Where is the best place to go that summarize all that I need to know about this car. I'll be racing carpet foam w/ 13.5 brushless. And possilbly parking lot too. I use to race with a tc3 and I see that this is a different animal. All help will be appreciated.
Thanks
setup
Hi
Looking to get back into tc racing, I picked a used 415msx of rctech. Where is the best place to go that summarize all that I need to know about this car. I'll be racing carpet foam w/ 13.5 brushless. And possilbly parking lot too. I use to race with a tc3 and I see that this is a different animal. All help will be appreciated.
Thanks
Looking to get back into tc racing, I picked a used 415msx of rctech. Where is the best place to go that summarize all that I need to know about this car. I'll be racing carpet foam w/ 13.5 brushless. And possilbly parking lot too. I use to race with a tc3 and I see that this is a different animal. All help will be appreciated.
Thanks
I ended up running 2 top decks to stiffen it all up ,
Ps all depends on the type of carpet ur running on
Cheers Mark M