Go Back  R/C Tech Forums > General Forums > Electric On-Road
Awesomatix EP Touring Car (A700 Shaft Drive) >

Awesomatix EP Touring Car (A700 Shaft Drive)

Like Tree29Likes

Awesomatix EP Touring Car (A700 Shaft Drive)

Reply

Old 01-11-2018, 11:36 AM
  #9571  
Tech Adept
iTrader: (1)
 
jdawg81's Avatar
 
Join Date: Jan 2012
Location: Vancouver, BC
Posts: 192
Trader Rating: 1 (100%+)
Default

Originally Posted by phatboislim View Post
newb awesomatix owner here with a newb awesomatix A700 question...how the hell do you get the lower motor mount screw to secure the motor down?!?
I usually set the gear mesh and tighten the top screw. Then remove the pinion gear so I have clear access to the bottom screw. Once that is done you can use a L shaped allen key to tighten the bottom screw. Or you can use a ball hex driver and slide it through between the universal bone and top turnbuckles to reach the bottom screw. That's how I normally do it but I don't have my car in front of me so I might not be 100% correct on that. Hope this helps.
phatboislim likes this.
jdawg81 is offline  
Reply With Quote
Old 01-11-2018, 12:02 PM
  #9572  
Tech Elite
iTrader: (37)
 
howardcano's Avatar
 
Join Date: Jan 2012
Location: Olathe, KS
Posts: 3,738
Trader Rating: 37 (100%+)
Default

I do the same as jdawg81, with balldriver, no L-wrench. I use cap head screws so I can use a larger balldriver to lessen the chances of stripping the head.

It also helps to grind a little off the OD of the bottom screw head. Some of them can be a tight fit; there isn't much clearance.
phatboislim likes this.
howardcano is offline  
Reply With Quote
Old 01-11-2018, 03:21 PM
  #9573  
Tech Adept
iTrader: (2)
 
Join Date: Dec 2015
Posts: 215
Trader Rating: 2 (100%+)
Default

Originally Posted by howardcano View Post
I do the same as jdawg81, with balldriver, no L-wrench. I use cap head screws so I can use a larger balldriver to lessen the chances of stripping the head.

It also helps to grind a little off the OD of the bottom screw head. Some of them can be a tight fit; there isn't much clearance.
Thatís a great idea on the socket head cap screws instead of the button ones!

Iím assuming neither of you have the latest version of the motor mount?
RollingChicane2 is offline  
Reply With Quote
Old 01-11-2018, 04:28 PM
  #9574  
Tech Elite
iTrader: (37)
 
howardcano's Avatar
 
Join Date: Jan 2012
Location: Olathe, KS
Posts: 3,738
Trader Rating: 37 (100%+)
Default

Originally Posted by RollingChicane2 View Post
Thatís a great idea on the socket head cap screws instead of the button ones!

Iím assuming neither of you have the latest version of the motor mount?
I'm guessing no for me. All of my cars were purchased used, and all have the same mount.
howardcano is offline  
Reply With Quote
Old 01-11-2018, 04:43 PM
  #9575  
Tech Adept
iTrader: (2)
 
Join Date: Dec 2015
Posts: 215
Trader Rating: 2 (100%+)
Default

Originally Posted by howardcano View Post
I'm guessing no for me. All of my cars were purchased used, and all have the same mount.
The last generation motor mount is excellent. It is a two piece design that allows you to mount the motor to an aluminum piece and then that piece will slide on a mount that is bolted to the chassis that has a set screw to allow ultra-fine adjustment of the mesh and when you have it where you want it, you tighten two screws perpendicular to the motor to bolt the two pieces together. No more difficulty setting mesh or tightening of screws.

That explanation was probably terrible....sorry.

I have an Evo 2 that is the most recent design with a lot of other options. I run it in VTA and itís phenomenal.
RollingChicane2 is offline  
Reply With Quote
Old 01-11-2018, 06:53 PM
  #9576  
Tech Addict
iTrader: (24)
 
Join Date: Nov 2016
Posts: 510
Trader Rating: 24 (97%+)
Default

What’s ur setup for vta
Rcforlife13 is offline  
Reply With Quote
Old 01-18-2018, 03:12 AM
  #9577  
Tech Fanatic
iTrader: (1)
 
Join Date: Jul 2014
Location: Hong Kong
Posts: 823
Trader Rating: 1 (100%+)
Default

Hey folks

I'm running 17.5T evo 2 with alum chassis and carbon top deck. Are folks also running the center spine stiffener when also running top deck or removing it?
WagwanBumba is offline  
Reply With Quote
Old 01-19-2018, 09:08 AM
  #9578  
Tech Champion
iTrader: (27)
 
hanulec's Avatar
 
Join Date: Sep 2007
Location: @ the post office
Posts: 8,713
Trader Rating: 27 (100%+)
Default

Originally Posted by WagwanBumba View Post
Hey folks

I'm running 17.5T evo 2 with alum chassis and carbon top deck. Are folks also running the center spine stiffener when also running top deck or removing it?
you need to run the AM33 spines
hanulec is offline  
Reply With Quote
Old 05-22-2018, 05:24 AM
  #9579  
Tech Elite
iTrader: (36)
 
jlfx car audio's Avatar
 
Join Date: Nov 2007
Location: jackson,tn
Posts: 3,529
Trader Rating: 36 (100%+)
Default

Funny the last msg in this area is about the am33 which is what I'm looking for to buuld my first shaft car .
Anyone got a spare am30/33-5 ?
jlfx car audio is offline  
Reply With Quote
Old 06-19-2018, 04:14 AM
  #9580  
Tech Rookie
 
Join Date: Jun 2013
Location: H.K.
Posts: 11
Default

Hi engineers and folks,

Will A700-EvoIIC be produced on request? It cannot be back-ordered on the websites.

I heard that ST13 and ST14 will be discontinued and must change to IFJ and IRJ. Is it true? I think my 2 Ball Diffs will be useless if those bones are unavailable.

Thanks
ricekwan is offline  
Reply With Quote
Old 06-20-2018, 05:33 AM
  #9581  
Tech Initiate
 
!Mad Max!'s Avatar
 
Join Date: Jul 2011
Location: Germany
Posts: 49
Default

Hi ricekwan,

For A700-EvoIIC you can ask via the Support Email from Awesomatix, or your local distributor.
ST13 and ST14 is discontinued/replaced with IFJ and IRJ at Awesomatix.
But ST13 and ST14 can be still available at some Distributors.

A700-AT03M is suitable for the use of IFJ.
A700-GD2 is suitable for the use of IRJ.

What are the advantage of Ball Diffs for A700 over the Gear Diff in your Opinion ? And in which Class do you run with the BD1 Ball Diff ?

Regards, Max
!Mad Max! is offline  
Reply With Quote
Old 06-24-2018, 12:01 AM
  #9582  
Tech Rookie
 
Join Date: Jun 2013
Location: H.K.
Posts: 11
Default

Hi Max!
Thanks to your help. I like the ball diff since it is a breakthrough to have diff oil in it. It is so smooth that I feel it helps on corner exit, compared with GD1. However it has an issue of oil leak at the case (AT01/AT02). Will try to get GD2. I run modified with X22 10.5T or X20 8.5T.

I have a mod on the RFG to let it float more. It helps me a lot on the real grip. Any other mods to share with us?


Last edited by ricekwan; 06-24-2018 at 12:02 AM. Reason: correction
ricekwan is offline  
Reply With Quote
Old 06-26-2018, 07:02 AM
  #9583  
Tech Elite
iTrader: (36)
 
jlfx car audio's Avatar
 
Join Date: Nov 2007
Location: jackson,tn
Posts: 3,529
Trader Rating: 36 (100%+)
Default

whats the internal ration of a evo2 car ? just to clarify.
i just find it odd im running a 5.1 fdr (figuring @ a 2.09 internal) with a 25.5 on a larger fast layout track and turning the fastest laps with it

Last edited by jlfx car audio; 06-26-2018 at 07:21 AM.
jlfx car audio is offline  
Reply With Quote
Old 06-26-2018, 08:43 AM
  #9584  
Tech Fanatic
 
chiefj48's Avatar
 
Join Date: Mar 2010
Location: Palm Bay, Florida
Posts: 913
Default

2.08 internal
chiefj48 is offline  
Reply With Quote

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service