Go Back  R/C Tech Forums > General Forums > Electric On-Road
7700Mamba Max motor on TT01, need help >

7700Mamba Max motor on TT01, need help

7700Mamba Max motor on TT01, need help

Old 06-05-2008, 06:32 PM
  #1  
Tech Rookie
Thread Starter
 
Join Date: Jun 2008
Posts: 3
Default 7700Mamba Max motor on TT01, need help

Hi, I bought a 7700kvMM to fit on my TT01.. and.. I don't know what pinion and spur to use.

I wish to have long run time, I don't need to accelerate pretty fast..

What would be the best mix for me

I have the stock 61t spur.. an 58 and a 55 one,

I have a 19, 20 and 21t pinions

I have a 4200mh intellect 6 cells.

What are the best mix for me?

thanks alot!

-Nick (23years, Montréal)! Hi!! everybody by the way


Oh and any TT01 owner tried the 7700 on the car? Is it going to break the f$?&*%? up?
WhyDidIBuyA7700 is offline  
Old 06-05-2008, 06:44 PM
  #2  
Tech Fanatic
iTrader: (7)
 
Mooshu Beef's Avatar
 
Join Date: Jul 2007
Location: State of Insanity
Posts: 790
Trader Rating: 7 (100%+)
Default

Holy crap man... Good luck with the 7700 motor.

I have a 6900 motor that I dropped into a TT-01 with all stock drivetrain except an aluminum driveshaft (A MUST for anything more than silver can). It held up decently until I crashed into a wall... and shattered both left knuckles and a dogbone.

I would suggest 19:61. Make sure you set your timing to 0 degrees, and punch control right so that the temp will be low.

OR you can run it as is with that gearing, and see your temps. What kind of driving do you do?


MAKE SURE you tighten all the screws and that the motor is fully on the motor mount. You have a metal mount, right?
Mooshu Beef is offline  
Old 06-05-2008, 07:07 PM
  #3  
Tech Rookie
Thread Starter
 
Join Date: Jun 2008
Posts: 3
Default

Well.. I do have a aluminium shaft, and full ball bearings. But I don't have a metal motor mount.

Thanks, I will try 19:61 and position 0 to be safe.

My kind of driving hmm.. I'd say doing straight line in the street... nothing special yet.

thanks!

Last edited by WhyDidIBuyA7700; 06-05-2008 at 07:18 PM.
WhyDidIBuyA7700 is offline  
Old 06-05-2008, 07:28 PM
  #4  
Tech Fanatic
iTrader: (7)
 
Mooshu Beef's Avatar
 
Join Date: Jul 2007
Location: State of Insanity
Posts: 790
Trader Rating: 7 (100%+)
Default

Okay, I would get a metal motor mount, and heatsink if you don't have one already.

While you are trying this, if you hear any sort of grinding don't gas it too hard, and open up the gear case immediately. A grinding sound means that you are stripping a spur usually...so be careful.
Mooshu Beef is offline  

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.