Tekin RS ESC sensored
#8806
Tech Master
iTrader: (8)
Just got my new RS and need a little help. I installed all the updates for the hotwire interface. I then connected my esc to update it. I can't figure out how to set the turbo setting? Can someone help me figure out what I'm overlooking please?
The latest firmware update listed was 198.
Thanks for the help!
The latest firmware update listed was 198.
Thanks for the help!
You will need to unistall the current version and install the V200
If you send me your e-mail address I can forward it to you with Randy's explanation on how it works
Last edited by RC-ProSpeed; 12-19-2009 at 08:26 PM.
#8808
Tech Lord
iTrader: (103)
is this what the turbo kicking in is meant to sound like, sounds like the motors going to pop
http://www.youtube.com/watch?v=_ddrinmKwYk
http://www.youtube.com/watch?v=_ddrinmKwYk
#8809
That's funny, never though to put up a vid of the turbo...
Wait til you "hear" what's coming...
Wait til you "hear" what's coming...
#8812
Tech Elite
iTrader: (29)
i need the vegas 200 software please ... [email protected] and also im new w/tekin, after the update goes thru it says restoring factory defaults, im assuming the settings i uploaded are in there and it just reverts back to default? anyhow thanx...i had the vegas 200 just lost it...do you delete the tekin hotwire software, than re-install with the newer vegas200...sorry for all the newb q's here, jus wanna get the most outs this esc...
tommy
tommy
#8813
Tech Champion
What radio are you trying to test the fail safe on?
#8815
Tech Lord
iTrader: (103)
i need the vegas 200 software please ... [email protected] and also im new w/tekin, after the update goes thru it says restoring factory defaults, im assuming the settings i uploaded are in there and it just reverts back to default? anyhow thanx...i had the vegas 200 just lost it...do you delete the tekin hotwire software, than re-install with the newer vegas200...sorry for all the newb q's here, jus wanna get the most outs this esc...
tommy
tommy
#8816
Tech Master
iTrader: (18)
Randy
Any improvments in software to equal the mamba pro for oval racing yet? Doing my best to not buy the mamba pro but its not easy when I see others have added close to 2 laps to their best record so far in 1S pancar. Also at the big usowc dirt oval race where 2S 13.5 classes were run ppl were buying them like candy LOL.
Any improvments in software to equal the mamba pro for oval racing yet? Doing my best to not buy the mamba pro but its not easy when I see others have added close to 2 laps to their best record so far in 1S pancar. Also at the big usowc dirt oval race where 2S 13.5 classes were run ppl were buying them like candy LOL.
#8817
Yes.
#8819
Tech Regular
Hi Everyone,
I have been reading this thread for a while, I use a speedpasion GT2 at the moment but I want to up grade. The RS pro is on my radar for 13.5 and 10.5 touring car racing. I have been racing for around 6 years now but I like most people I race with are really put off the likes of the RS esc and GM etc because they are so complicated to setup and programme. I would really like to buy on RS but iam holding back because of this. Now to the point, if some one was to publish either on here or on the Tekin website a step by step guide from opening the box to installing the hotwire software and programming including all the confusing stuff about about windows xp/vista etc then I would buy one straight away.
I know all the info is prob already in this thread some where but a step by step guide for muppets like me would be a big help. Just a thought
I have been reading this thread for a while, I use a speedpasion GT2 at the moment but I want to up grade. The RS pro is on my radar for 13.5 and 10.5 touring car racing. I have been racing for around 6 years now but I like most people I race with are really put off the likes of the RS esc and GM etc because they are so complicated to setup and programme. I would really like to buy on RS but iam holding back because of this. Now to the point, if some one was to publish either on here or on the Tekin website a step by step guide from opening the box to installing the hotwire software and programming including all the confusing stuff about about windows xp/vista etc then I would buy one straight away.
I know all the info is prob already in this thread some where but a step by step guide for muppets like me would be a big help. Just a thought
#8820
Probably what's going on is that your RS has a newer version software than your hotwire software has.
Once you get V200 downloaded, update the firmware on your RS to 200 and you'll have all the current adjustments.