Tekin RS ESC sensored
08-11-2009, 06:31 AM
#5896
The ESC doesn't even respond to the Hotwire software at all the old version or the new version. When powered on the lights are very dim and the steering works but no throttle. I have spent several hours working on this already and just can't figure it out. If anyone can help me please do.
08-11-2009, 06:34 AM
#5897
Tech Master
http://www.youtube.com/watch?v=Pb--yQonviA
here is the track and what layout we will be running
thanks for the input guys
here is the track and what layout we will be running
thanks for the input guys
Boost 10 to 15
Tekin 10,5 motor timing 10 to 12
6,6FDR to start with
Turbo max
gear heavier if needed
08-11-2009, 06:36 AM
#5898
Tech Master
The ESC doesn't even respond to the Hotwire software at all the old version or the new version. When powered on the lights are very dim and the steering works but no throttle. I have spent several hours working on this already and just can't figure it out. If anyone can help me please do.
08-11-2009, 06:45 AM
#5901
From one of Randy's earlier posts: "Dim lights can be software not installed properly and or install issues.
First do a factory reset, if that doens't cure it. Re install older software, then upgrade it once it's working properly."
I'm a little fuzzy on the factory reset, It says to press and hold the inc button, and then press and hold the mode button simultaneously for three seconds. after 3 seconds the leds will ramp up in sets of three.
First do a factory reset, if that doens't cure it. Re install older software, then upgrade it once it's working properly."
I'm a little fuzzy on the factory reset, It says to press and hold the inc button, and then press and hold the mode button simultaneously for three seconds. after 3 seconds the leds will ramp up in sets of three.
08-11-2009, 06:51 AM
#5902
From one of Randy's earlier posts: "Dim lights can be software not installed properly and or install issues.
First do a factory reset, if that doens't cure it. Re install older software, then upgrade it once it's working properly."
I'm a little fuzzy on the factory reset, It says to press and hold the inc button, and then press and hold the mode button simultaneously for three seconds. after 3 seconds the leds will ramp up in sets of three.
First do a factory reset, if that doens't cure it. Re install older software, then upgrade it once it's working properly."
I'm a little fuzzy on the factory reset, It says to press and hold the inc button, and then press and hold the mode button simultaneously for three seconds. after 3 seconds the leds will ramp up in sets of three.
I have tried to reset the ESC but it doesn't respond?
08-11-2009, 07:11 AM
#5904
The ESC doesn't even respond to the Hotwire software at all the old version or the new version. When powered on the lights are very dim and the steering works but no throttle. I have spent several hours working on this already and just can't figure it out. If anyone can help me please do.
08-11-2009, 07:13 AM
#5905
Will someone please email me the 200 software. I hvae no team driver to go to. I would greatly appreciate it.
[email protected]
[email protected]
08-11-2009, 07:40 AM
#5906
Tech Master
Will someone please email me the 200 software. I hvae no team driver to go to. I would greatly appreciate it.
[email protected]
[email protected]
It's with the info of Randy
08-11-2009, 07:46 AM
#5907
Tech Master
08-11-2009, 08:20 AM
#5908
Guys,
If you get dim lights on an RS:
Make sure no buttons are stuck, try to flash the speedo back to older software, then back up to current. Make sure it's plugged in all the way into the hotwire.
A factory reset can help bring the speedo back to life if it doesn't respond, this is all in your instructions.
Set your epa's as you normally would. On my Dx3r I run 150 and 150. On my M8 I ran 140 and 140 to keep 'em even.
On the subject of push control: This is the opposite of drag brake. I've not yet seen a case where anyone needed this in 1/10 racing. We turned this feature on in brushless mode mostly for 1/8 offroad/onroad racing. In most cases turn it off.
The "beta" in the file name is do to this not being uploaded on the website. This will still be a ways off before that happens. We like to get one on one with customers that get this software so we can go over it's use and proper setup.
If you get dim lights on an RS:
Make sure no buttons are stuck, try to flash the speedo back to older software, then back up to current. Make sure it's plugged in all the way into the hotwire.
A factory reset can help bring the speedo back to life if it doesn't respond, this is all in your instructions.
Set your epa's as you normally would. On my Dx3r I run 150 and 150. On my M8 I ran 140 and 140 to keep 'em even.
On the subject of push control: This is the opposite of drag brake. I've not yet seen a case where anyone needed this in 1/10 racing. We turned this feature on in brushless mode mostly for 1/8 offroad/onroad racing. In most cases turn it off.
The "beta" in the file name is do to this not being uploaded on the website. This will still be a ways off before that happens. We like to get one on one with customers that get this software so we can go over it's use and proper setup.
08-11-2009, 08:25 AM
#5910
Randy, I sent you an email. Thanks.
