Go Back  R/C Tech Forums > General Forums > Electric On-Road
23T motor thread >

23T motor thread

23T motor thread

Old 06-30-2004, 03:57 PM
  #571  
Tech Master
 
PizzaDude's Avatar
 
Join Date: Nov 2002
Location: Parts Unkown
Posts: 1,088
Default

Dave,

That indeed is a major diference....
Did you test the gunmetall with standup endbell also?
I'm asking because you mentioned standup kinda being the trend for 23t.

Regards,
Pizza
PizzaDude is offline  
Old 06-30-2004, 04:11 PM
  #572  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Default

Originally posted by PizzaDude
Dave,

That indeed is a major diference....
Did you test the gunmetall with standup endbell also?
I'm asking because you mentioned standup kinda being the trend for 23t.

Regards,
Pizza
Nope the RR only came in a Laydown version..

RPM Versions of 23T motors seem to be OK with the brag brake effect..but a torque version with laydown brushes....is a pain..with oneways
-Dave
JDM_DOHC_SiR is offline  
Old 06-30-2004, 04:52 PM
  #573  
Registered User
 
Join Date: Apr 2003
Posts: 992
Default

i have over 30+ of these motors that I have tested and run and I have only found a few that you gear the same.. ..but most 23T`s are geared between 5.3~6.6ish for a medium size track and also what version motor you have
Thanks Dave, I might get Katana 23T TS.
Aku-Man is offline  
Old 06-30-2004, 04:56 PM
  #574  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Default

Originally posted by Aku-Man
Thanks Dave, I might get Katana 23T TS.
Good motor..I really am begining to like thsi one from ORION.. it really shines on the track...huge power out of the hole on starts!!this motor and the Kawada VT-R seem to be the kings for torque right now... my Lap times are about .5 faster per lap over my RPM based motors
-Dave
JDM_DOHC_SiR is offline  
Old 06-30-2004, 05:04 PM
  #575  
Registered User
 
Join Date: Apr 2003
Posts: 992
Default

Good motor..I really am begining to like thsi one from ORION.. it really shines on the track...huge power out of the hole on starts!!this motor and the Kawada VT-R seem to be the kings for torque right now... my Lap times are about .5 faster per lap over my RPM based motors


What is best gear to start with this motor?
Aku-Man is offline  
Old 06-30-2004, 05:09 PM
  #576  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Default

Originally posted by Aku-Man


What is best gear to start with this motor?
how big is your track.??
each motor will vary a bit but I can get you in the ball park
JDM_DOHC_SiR is offline  
Old 06-30-2004, 05:18 PM
  #577  
Registered User
 
Join Date: Apr 2003
Posts: 992
Default

about small/medium.
Aku-Man is offline  
Old 06-30-2004, 05:21 PM
  #578  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Default

Originally posted by Aku-Man
about small/medium.
How long is your straight away in Meters.??
JDM_DOHC_SiR is offline  
Old 06-30-2004, 05:22 PM
  #579  
Registered User
 
Join Date: Apr 2003
Posts: 992
Default

no idea. about 32~48 normal walking steps, I think.
Aku-Man is offline  
Old 06-30-2004, 05:26 PM
  #580  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Default

Originally posted by Aku-Man
no idea. about 32~48 normal walking steps, I think.
sheesh are those baby steps of giant steps ...
I can helpout more if you knew
JDM_DOHC_SiR is offline  
Old 06-30-2004, 05:29 PM
  #581  
Registered User
 
Join Date: Apr 2003
Posts: 992
Default

I'm bad at eye measuring things.

Just normal walking...
Aku-Man is offline  
Old 06-30-2004, 05:36 PM
  #582  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Default

Originally posted by Aku-Man
I'm bad at eye measuring things.

Just normal walking...
OK then..small/med track..hmm with the Orion TS try 5.8 for starters if you need more top end try one or two teeth bigger(64P)
-Dave
JDM_DOHC_SiR is offline  
Old 07-01-2004, 06:25 AM
  #583  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Default

Originally posted by Neil Rabara
Gunmetal. It's for the upcoming Tamiya North American Nationals here in California.
I have not frogot about ya` Neil.. just been busy today.. i`ll get back to ya in a bit
-Dave
JDM_DOHC_SiR is offline  
Old 07-02-2004, 04:51 PM
  #584  
Tech Champion
iTrader: (31)
 
JDM_DOHC_SiR's Avatar
 
Join Date: Aug 2002
Location: Chula Vista, CA
Posts: 9,087
Trader Rating: 31 (100%+)
Thumbs up New Luna Glory 23T stocks

Hey Guys I just picked up 2 new Luna 23T stock motors yesterday that I will be testing today & tommorow

Luna Glory Limmitied AT
Luna Glory Limmited ATT

Both of them are based of the newer Atlas FORCE vice the last version which was based off of the Yokomo new can.?


Also picked up a new tamiya TZ motor to test too
hope to have some good feed back from these motors on the track and on the dyno
-Dave
JDM_DOHC_SiR is offline  
Old 07-02-2004, 07:14 PM
  #585  
Tech Adept
 
alch's Avatar
 
Join Date: Nov 2003
Location: Tokyo, Japan
Posts: 188
Default Re: New Luna Glory 23T stocks

Originally posted by JDM_DOHC_SiR
Hey Guys I just picked up 2 new Luna 23T stock motors yesterday that I will be testing today & tommorow

Luna Glory Limmitied AT
Luna Glory Limmited ATT

Both of them are based of the newer Atlas FORCE vice the last version which was based off of the Yokomo new can.?


Also picked up a new tamiya TZ motor to test too
hope to have some good feed back from these motors on the track and on the dyno
-Dave
New Luna?! Have you run it on the Dyno yet? I like my current Luna alot (LII in a ST can) ..
I take it the ATT is the torque version? Both Standup? I couldn't find it on their website (still looking though) I think i might have to pick one up today, give it a quick run tomorrow morning!
I will be getting to the track around 6:30 tomorrow.. Get some practice in!

I think i understand the drag brake effect or Laydown motors now too
alch is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.