Around The Table With Paul Lemieux(RC-America/Thunderpower)
#1328
I'll ask again, Knowing your not running a 10.5 in your 1/12, and seeing EA is looking in. What is a good rollout for 1/12 with the duo2 10.5 on 1S, and can timing recomendations as well as esc timing. Medium to small track ( DRCW) also plan to go to Mimi's. EA any help??
Thanks,
Tim
Thanks,
Tim
#1329
Hi dave, i didnt get a Pm.
Not sure yet byt maybe.
Jim should be their.
definately EA's question, sorry, Thanks.
Not sure yet byt maybe.
I'll ask again, Knowing your not running a 10.5 in your 1/12, and seeing EA is looking in. What is a good rollout for 1/12 with the duo2 10.5 on 1S, and can timing recomendations as well as esc timing. Medium to small track ( DRCW) also plan to go to Mimi's. EA any help??
Thanks,
Tim
Thanks,
Tim
#1331
Team EAM
iTrader: (79)
I'll ask again, Knowing your not running a 10.5 in your 1/12, and seeing EA is looking in. What is a good rollout for 1/12 with the duo2 10.5 on 1S, and can timing recomendations as well as esc timing. Medium to small track ( DRCW) also plan to go to Mimi's. EA any help??
Thanks,
Tim
Thanks,
Tim
Last year with a DUO I ran middle hole timing and rolled out around a 48-50mm in 4 cell. That was before the SPX speedo's and timing advance. I have not ran 10.5 this year with the newer speedo's or 1S.
Just a guess but with 1S and the timing advance now I would start around that same rollout with profile7 on the SPX.
Thanks
EA
#1332
Wow, I was heading in a whole wrong direction. I was following the 65-70mm rollout, cranking can timing up 7 hash marks, and bumping esc timing middle ways up. ( I'm running the SP esc) Not questioning or doubting your input, I really appreciate it. Just the info I have gathered from surfing the forum. The car is setup pretty much like that now, and we plan on going down to test Sunday, so I'll carry the gear needed to change to that and see what happens. TC, brushless, lipo we're good, going from brushed , nimh on the 1/12 I'm at a loss. Should i concern myself with the dyno RPM results that came with the motor for rollout input??
Thanks alot Paul and EA for your help.
Tim
Thanks alot Paul and EA for your help.
Tim
#1333
Tech Master
iTrader: (26)
Hey Paul,
Do you have any suggestions or techniques to build driving consistency? I am at the stage of being able to drive without crashing but I am still developing the best lines to get around the track. My car feels drivable in that it doesn't have too much steering but enough to get around fairly well.
If you have time, here is the result from my best round last night. I am car number 5.
http://track.nexusracing.com/dirLIST...nd_3/h4r3.html
And the track..
http://track.nexusracing.com/pictures.html
P.S. - How is your son? It's been awhile since his birth - he must be getting big!
Do you have any suggestions or techniques to build driving consistency? I am at the stage of being able to drive without crashing but I am still developing the best lines to get around the track. My car feels drivable in that it doesn't have too much steering but enough to get around fairly well.
If you have time, here is the result from my best round last night. I am car number 5.
http://track.nexusracing.com/dirLIST...nd_3/h4r3.html
And the track..
http://track.nexusracing.com/pictures.html
P.S. - How is your son? It's been awhile since his birth - he must be getting big!
#1334
OK ran the 1/12 today. Started with 35/78 gearing 45mm tires stock can timing 22.5 degrees in the esc start up turned all the way up. Car was soso top speed motor was stone cold. Jumped up to a 38T pinion and still cold motor. Put a 40T on and it thermaled the esc after about 3 minutes. I used the 16ga TQ wires from esc to motor, and I pretty sure thats my problem. Not getting the juice to the motor. Car had a ton of punch if I touched the wall under acceleration it would wheelie like my 1/8 nitro car.
Paul sorry not trying to jack your thread.
Are you coming to the Nats at Mimi's?? I'm planning for me and my son to go, He's running the 007 in 17.5 rubber tire and I'll run 1/12 something. Hopefully get a chance to meet you face to face.
Tim
Paul sorry not trying to jack your thread.
Are you coming to the Nats at Mimi's?? I'm planning for me and my son to go, He's running the 007 in 17.5 rubber tire and I'll run 1/12 something. Hopefully get a chance to meet you face to face.
Tim