4LikesTamiya TRF416 / TRF416WE / TRF416X
03-30-2009, 09:03 PM
#4966
Tech Regular
I do convert Jilles setup from LRP Masters into PDF, here is the document! Let me know in case of any mistake!
For those who are looking for setups, there is Ed website or this page as alternative.
Jilles, will it be possible to get some info about you TRF guys used during WC in Bangkok?
For those who are looking for setups, there is Ed website or this page as alternative.
Jilles, will it be possible to get some info about you TRF guys used during WC in Bangkok?
03-30-2009, 11:17 PM
#4967
Originally Posted by JGH
Hello guys,
You guys are absolutely right about the fact that we don't share a lot of info and set-ups on this forum.
I have tried to keep up in the beginning on the TRF 416 topic but there are so many posts I get a little confused.
Nevertheless I try to get more involved in the forum again or maybe if you guys think it's a good idea I can start my own thread?
Attached is my set-up from the LRP race yesterday.
Jilles Groskamp
You guys are absolutely right about the fact that we don't share a lot of info and set-ups on this forum.
I have tried to keep up in the beginning on the TRF 416 topic but there are so many posts I get a little confused.
Nevertheless I try to get more involved in the forum again or maybe if you guys think it's a good idea I can start my own thread?
Attached is my set-up from the LRP race yesterday.
Jilles Groskamp
03-31-2009, 01:19 AM
#4968
Originally Posted by TryHard
Hmm, where were you running the shocks in the arm? 1 or 2? Could have tried moving it back into 2 on the arm, if in 1.
Maybe 4.5mm or 4mm might have worked better for initial bite, but maybe would have lost some eleswhere. Could also have narrowed the car down, with 0.5mm or 0mm on the hexes.... erm other ideas, softer oil in the front?
I take it that was the STCC? Might have to break mine out at some point outdoors this year....I'm getting the itch already
Maybe 4.5mm or 4mm might have worked better for initial bite, but maybe would have lost some eleswhere. Could also have narrowed the car down, with 0.5mm or 0mm on the hexes.... erm other ideas, softer oil in the front?
I take it that was the STCC? Might have to break mine out at some point outdoors this year....I'm getting the itch already
03-31-2009, 01:22 AM
#4969
Originally Posted by JGH
Hello guys,
You guys are absolutely right about the fact that we don't share a lot of info and set-ups on this forum.
I have tried to keep up in the beginning on the TRF 416 topic but there are so many posts I get a little confused.
Nevertheless I try to get more involved in the forum again or maybe if you guys think it's a good idea I can start my own thread?
Attached is my set-up from the LRP race yesterday.
Jilles Groskamp
You guys are absolutely right about the fact that we don't share a lot of info and set-ups on this forum.
I have tried to keep up in the beginning on the TRF 416 topic but there are so many posts I get a little confused.
Nevertheless I try to get more involved in the forum again or maybe if you guys think it's a good idea I can start my own thread?
Attached is my set-up from the LRP race yesterday.
Jilles Groskamp
Really nice of you to take time out Jilles... I am sure you will get bombarded with questions now..... but atleast we will get the correct answers
and many congtats on your results!
03-31-2009, 02:39 AM
#4970
Have you girls seen this? I know it's steel cups, but maybe you can use it for back up....
http://shopping.rcmodel.hk/product_i...vrsqa8bmdptdt2
http://shopping.rcmodel.hk/product_i...vrsqa8bmdptdt2
03-31-2009, 02:53 AM
#4971
Tech Adept
Hello everyone,
Thanks for all your comments yesterday.
I just started a new thread called: "ask" Jilles Groskamp Tamiya 416(WE) / SpeedPassion motors.
I will try to help all of you as good as I can!
Jilles Groskamp
Thanks for all your comments yesterday.
I just started a new thread called: "ask" Jilles Groskamp Tamiya 416(WE) / SpeedPassion motors.
I will try to help all of you as good as I can!
Jilles Groskamp
03-31-2009, 03:06 AM
#4972
question: is there a thicker upper deck for the WE? i would like to know if i could upgrade/use it.. and if so how thick is it?
03-31-2009, 03:13 AM
#4973
There is no official Tamiya part, maybe someone else makes one?! But why?
03-31-2009, 07:17 AM
#4975
i'm thinking 4 degrees...
03-31-2009, 07:20 AM
#4976
Originally Posted by sohlman
Are the Tamiya #51293 TA05-IFS hub-carriers 2 degrees or 4 degrees?
03-31-2009, 10:52 AM
#4977
Originally Posted by TryHard
Simple answer.... cause there is not really any impetus from anyone within TRF to do so 
I know TRF USA is giving it a stab (massively comendable guys ), but from the EU and Japan boys and girls, it's a bit hard... Jilles poped on here for a while, but hasn't been here for a long time now.
Also, Marc is quite reknowned for not noting down his setups
Any of the ones you find, will tend to be taken by other people at the races, and then passed on...
HiH
Ed
I know TRF USA is giving it a stab (massively comendable guys
), but from the EU and Japan boys and girls, it's a bit hard... Jilles poped on here for a while, but hasn't been here for a long time now. Also, Marc is quite reknowned for not noting down his setups
Any of the ones you find, will tend to be taken by other people at the races, and then passed on...
HiH
Ed
And it's great to see Jilles here again....
03-31-2009, 06:43 PM
#4978
Originally Posted by Ricky/C
There is no official Tamiya part, maybe someone else makes one?! But why?
P.s. for you guys with ageing 416s, check your spur gear spindle for wear underneath the pulleys. Mine are sloppy as and visibly worn!
04-01-2009, 12:44 AM
#4980
Center shaft.
Originally Posted by B18C Turbo
what is a spur gear spindle?
