Tamiya TRF416 / TRF416WE / TRF416X
#4068
Tech Apprentice
Hi Stilo, where have you taken your droop setting from? is it from the ground
up to the center of the axle??
any idea how your setup compares to rheinhards ect?
up to the center of the axle??
any idea how your setup compares to rheinhards ect?
#4069
Hi,
@Henry (Stilo): Thank you very much for your setup and Congrats to your reasonable second place! Very good job! I was wondering, that C-C will give enough steering in SuperStock. I have tested it a few times, but wasnt really pleased. I was running furst 1D-1B on DHI, later 1D-1C. But anything other was bad on my car.
In addition I was riding 1mm RC at the back (you was driving 0.5). I think with 1.0 it was more fluid to drive - but the fact is, that it was to slow.
@Henry (Stilo): Thank you very much for your setup and Congrats to your reasonable second place! Very good job! I was wondering, that C-C will give enough steering in SuperStock. I have tested it a few times, but wasnt really pleased. I was running furst 1D-1B on DHI, later 1D-1C. But anything other was bad on my car.
In addition I was riding 1mm RC at the back (you was driving 0.5). I think with 1.0 it was more fluid to drive - but the fact is, that it was to slow.
#4070
#4071
Don't know if this has been posted before, whats a good FDR (416 WE) to run with 9t 4300kv motor to race in an airconditioned indoor carpet track, size small to medium? Also which rubber tyre do you suggest with it?
Thanks.
Thanks.
#4072
If you look closely at what matters .. the geometry. Both cars are very similar. But if you have been paying attention to some of the stickers you may have seen for other products, "Blue is better!" .
#4073
Tech Master
iTrader: (2)
So after trying for a couple weeks I was finally able to break my 416. Does anybody know of a place, preferably stateside, I can get the C-hubs and knuckles for this? I think the ones that were on the car were the ones for the IFS as they took way too many hits to be the graphite. I'm not sure of that though as I got the car second hand, but they did not look like the same material as the ones that were on my 05R.
#4074
So after trying for a couple weeks I was finally able to break my 416. Does anybody know of a place, preferably stateside, I can get the C-hubs and knuckles for this? I think the ones that were on the car were the ones for the IFS as they took way too many hits to be the graphite. I'm not sure of that though as I got the car second hand, but they did not look like the same material as the ones that were on my 05R.
speedtechrc.com, ultraline.com, tamiyausa.com, ampdraw.com
#4075
Tech Addict
Check at the track what FDR others are running....
...
#4076
Is the one-way available anywhere as a separate unit?
#4077
#4078
Tech Addict
If you look about 10-15 posts back you will find it...
Yes, The original 416 came with one-way
3454520 TRF416 one way housing
9444623 TRF416 Freilauf Ausgänge
There is also availlable
49492 TRF416 "Middle One way" (Mittel-Freilauf Set)
...
Yes, The original 416 came with one-way
3454520 TRF416 one way housing
9444623 TRF416 Freilauf Ausgänge
There is also availlable
49492 TRF416 "Middle One way" (Mittel-Freilauf Set)
...
#4079
cant find the 416WE no stock with our LHS so i have to settle with the first released/original 416 i've already replaced the front one way with a spool
#4080