4LikesTamiya TRF416 / TRF416WE / TRF416X
10-06-2008, 08:50 AM
#2956
Tamiya's new Transpeed and Volac brushless system si made by LRP!!!! 
10-06-2008, 11:18 AM
#2957
Tech Adept
Originally Posted by t4m1y4niac
is the motor position on 416 WE more backward than original 416???
10-06-2008, 11:42 AM
#2958
will a trak power 4800 lipo fit in the 416
10-06-2008, 11:57 AM
#2959
Originally Posted by 94eg!
Tamiya's new Transpeed and Volac brushless system si made by LRP!!!!
post in this month Japan magzine
10-06-2008, 12:39 PM
#2960
Tech Adept
Originally Posted by eddie10
will a trak power 4800 lipo fit in the 416
Z
10-06-2008, 05:08 PM
#2961
what do you use from keeping it from sliding out or is it a non issue?
10-06-2008, 09:06 PM
#2962
Originally Posted by eddie10
what do you use from keeping it from sliding out or is it a non issue?
10-06-2008, 10:12 PM
#2963
Great pictures from Japanese magazine is shown up, but could anybody tell me if this is just proto or mass production 1.
In fact, i don't see any difference with the old 1, then the price is too much for 1 car which nor JMRCA could win, if this price is fixed i wonder to buy a HB Cylone Andy Moore then modified it with new parts:http://rc-japan.de/article.php?id=27...0b0c1247806b1d
In fact, i don't see any difference with the old 1, then the price is too much for 1 car which nor JMRCA could win, if this price is fixed i wonder to buy a HB Cylone Andy Moore then modified it with new parts:http://rc-japan.de/article.php?id=27...0b0c1247806b1d
10-07-2008, 02:00 AM
#2964
Tech Adept
Originally Posted by eddie10
what do you use from keeping it from sliding out or is it a non issue?
Otherwise 2 layers of tape, like Graig said should be OK.
Z
10-07-2008, 06:49 AM
#2966
Hi guys,
Will have V-Dezign 1-piece top decks for TRF 416 available in few days, if interested. Made from 2mm graphite to fit std Tamiya 416 without modifications.
Will have photos available very soon.
So if (distributors) interested, please contact me at
vesa(a)v-dezign.net (a)[email protected]
Will have V-Dezign 1-piece top decks for TRF 416 available in few days, if interested. Made from 2mm graphite to fit std Tamiya 416 without modifications.
Will have photos available very soon.
So if (distributors) interested, please contact me at
vesa(a)v-dezign.net (a)[email protected]
10-07-2008, 09:40 AM
#2967
Originally Posted by rcpoint
LRP lipo has a batt slots on the bottom so it stays in place.
Otherwise 2 layers of tape, like Graig said should be OK.
Z
Otherwise 2 layers of tape, like Graig said should be OK.
Z
10-07-2008, 01:14 PM
#2968
Originally Posted by rcpoint
LRP lipo has a batt slots on the bottom so it stays in place.
Otherwise 2 layers of tape, like Graig said should be OK.
Z
Otherwise 2 layers of tape, like Graig said should be OK.
Z
10-07-2008, 03:34 PM
#2969
Originally Posted by Hebiki
is that battery reversible? you can have the flat side down? or the "feet" side down? with connectors on both sides?
10-07-2008, 04:42 PM
#2970
OK so I threw both front CVD pins at racing last night, one in the first heat and one in the final 
I haven't cleaned or greased them since I built the car, so I'm thinking this is just a result of that. Do you guys have any other tips? I've heard of people filing a flat spot where the grub screw goes, and putting some heat shrink around the outside over the hole to stop them exiting into the steering knuckle, but I'm not sure if there is anything else I should do?
I haven't cleaned or greased them since I built the car, so I'm thinking this is just a result of that. Do you guys have any other tips? I've heard of people filing a flat spot where the grub screw goes, and putting some heat shrink around the outside over the hole to stop them exiting into the steering knuckle, but I'm not sure if there is anything else I should do?
