R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

Reply
 
Thread Tools Search this Thread
Old 02-21-2007, 07:15 AM   #1
Tech Adept
 
jino86's Avatar
 
Join Date: Sep 2006
Posts: 118
Default Tamiya TB EVO 5 front 1 way

Hi, recently bought a TB Evo 5 car kit and i'm planning to transfer the front 1 way to the back and the rear diff to the front. So, will the rear diff and front 1 way fit in and run like normal? and, will it some how cause any effect to the front 1 way when i put it to the rear? T.I.A
jino86 is offline   Reply With Quote
Old 02-21-2007, 07:40 AM   #2
Tech Master
 
Join Date: Dec 2004
Posts: 1,131
Default

Quote:
Originally Posted by jino86
Hi, recently bought a TB Evo 5 car kit and i'm planning to transfer the front 1 way to the back and the rear diff to the front. So, will the rear diff and front 1 way fit in and run like normal? and, will it some how cause any effect to the front 1 way when i put it to the rear? T.I.A
Putting your diff in the front is no problem. But, the one-way unit only spins in one direction. It won't work in the rear of the car.
Juan Aveytia is offline   Reply With Quote
Old 02-21-2007, 08:10 AM   #3
Tech Adept
 
jino86's Avatar
 
Join Date: Sep 2006
Posts: 118
Default

ok got it....Thx alot. Btw, is the spool for Tamiya TB evo 5 rear?

Last edited by jino86; 02-21-2007 at 08:21 AM.
jino86 is offline   Reply With Quote
Old 02-21-2007, 08:21 AM   #4
Tech Master
 
Join Date: Dec 2004
Posts: 1,131
Default

Quote:
Originally Posted by jino86
So does that mean if i out the front 1 way at the back it will act like a spool when going forward? ad the raer wheel will keep on spinning when i reverse
yes sir
Juan Aveytia is offline   Reply With Quote
Old 02-21-2007, 08:28 AM   #5
Tech Regular
 
Join Date: Jul 2006
Location: Brooklyn, New York
Posts: 490
Send a message via AIM to GuyIsDamGood
Default

I believe you can put a (Front) 1-Way in the Rear. I`ve heard about a few guys out there have did it.

Just put it in where it will always Rotate Forward.

Take Care
GuyIsDamGood is offline   Reply With Quote
Old 02-21-2007, 09:07 AM   #6
Tech Adept
 
jino86's Avatar
 
Join Date: Sep 2006
Posts: 118
Default

ok..what i did was i put the front 1 way at the rear and it will not spin forward when i throttle coz it move ony 1 direction...so i turned the 1 way other side and now it act as a spool..ok will that have any effect on the car of any thing as both my front bever are on thesame side
jino86 is offline   Reply With Quote
Old 02-21-2007, 09:15 AM   #7
Tech Regular
 
Join Date: Jul 2006
Location: Brooklyn, New York
Posts: 490
Send a message via AIM to GuyIsDamGood
Default

I don`t really know. I use Front and Rear Ball Diffs.

But.....Since you`re using that Set-Up; we can all learn from You. Try it and tell me(us) about it later.
-It looks like you`re looking for a Speed Set-Up.....?

Take Care
GuyIsDamGood is offline   Reply With Quote
Old 02-21-2007, 09:19 AM   #8
Tech Adept
 
jino86's Avatar
 
Join Date: Sep 2006
Posts: 118
Default

I'm using it for drifting..so wanna spool the rear and diff at the front..is there spool for evo 5 or any after market spool that will fit in with out any shimming?
jino86 is offline   Reply With Quote
Old 02-21-2007, 09:41 AM   #9
Tech Master
 
Join Date: Dec 2004
Posts: 1,131
Default

Quote:
Originally Posted by jino86
I'm using it for drifting..so wanna spool the rear and diff at the front..is there spool for evo 5 or any after market spool that will fit in with out any shimming?
Buy another aluminum diff joint set and JB weld them together and you will have your spool for the car.
Juan Aveytia is offline   Reply With Quote
Old 02-21-2007, 06:01 PM   #10
Tech Addict
 
Runin Ronin's Avatar
 
Join Date: Aug 2003
Location: Northern California
Posts: 618
Trader Rating: 12 (100%+)
Default

Quote:
Originally Posted by Juan Aveytia
Buy another aluminum diff joint set and JB weld them together and you will have your spool for the car.
I run a MSX MRE with the stock spool, I prefer a spool at the track I race and would like to try my EvoV more but, I have a difficult time running a one-way at my track.

Unless I have missed something... nobody makes a spool for the EvoV... has anyone used the JB Weld method to lock the stock EvoV one-way to make it a spool? Did you lock it with the drive cups intact?
Runin Ronin is offline   Reply With Quote
Old 02-21-2007, 06:19 PM   #11
Tech Addict
 
RussB's Avatar
 
Join Date: Aug 2005
Location: Sacramento
Posts: 736
Send a message via MSN to RussB
Default

just do the old-school trick with cardboard between the diff rings and the pulley. that's basically what losi did with their new slipper rings.
RussB is offline   Reply With Quote
Old 02-21-2007, 10:37 PM   #12
Tech Adept
 
jino86's Avatar
 
Join Date: Sep 2006
Posts: 118
Default

I managed to put the front 1 way in the rear and put it the other way so it will ony spin forward but the problem is i will have to turn the plastic case other way too, that means i;m not able to screw from the bottom to hold the protective case. So is it possible for me to run my car with open gear box? like other carkits? eg, barracuda R3 and other open gear kits
jino86 is offline   Reply With Quote
Old 02-22-2007, 12:40 AM   #13
Tech Master
 
Join Date: Dec 2004
Posts: 1,131
Default

Quote:
Originally Posted by Runin Ronin
I run a MSX MRE with the stock spool, I prefer a spool at the track I race and would like to try my EvoV more but, I have a difficult time running a one-way at my track.

Unless I have missed something... nobody makes a spool for the EvoV... has anyone used the JB Weld method to lock the stock EvoV one-way to make it a spool? Did you lock it with the drive cups intact?
It's really not a good idea to JB weld together. But, you can make it bullet proof if tamiya offers a metal gear for the evo5. Use the metal gear and JB weld it together with aluminum outdrives.
Juan Aveytia is offline   Reply With Quote
Old 02-22-2007, 10:13 AM   #14
Tech Regular
 
Join Date: Jul 2006
Location: Brooklyn, New York
Posts: 490
Send a message via AIM to GuyIsDamGood
Default

Wait for a few......Tamiya will make a Spool(Solid Axle) for the Evo 5(I don`t really know why they haven`t made one already).

Take Care
GuyIsDamGood is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tamiya TNS front arms MrUnlimited Nitro On-Road 1 08-11-2007 09:45 AM
Tamiya TB Evo 5 front 1 way jino86 Malaysian R/C Racers 4 02-26-2007 08:22 PM
WTB Tamiya TB-02 front one way SA22C'ya R/C Items: Wanted to Buy 0 07-08-2006 09:10 PM
Tamiya Front Tires sol44 R/C Items: For Sale/Trade 1 10-12-2003 08:09 AM
Alum Tamiya TA04 Front Steering Block / Front Upright Alvin Singapore R/C Racers 2 02-04-2002 07:50 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 06:41 PM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net