R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric On-Road

Reply
 
Thread Tools Search this Thread
Old 09-15-2009, 09:13 AM   #10786
Tech Adept
 
Redwood's Avatar
 
Join Date: Dec 2008
Location: Scotland
Posts: 188
Default

Quote:
Originally Posted by or8ital View Post
Did you use a routing bit pointed straight down at the chassis or did you do it by hand with the side of the bit?
I used the sanding drum, show here as attachment B:



I just ground away until the hole in the chassis was lined up with the bulkheads.

It's really easy, just make sure you wear a mask if you are grinding carbon fibre.

Regards

Neal

Last edited by Redwood; 09-15-2009 at 09:42 AM. Reason: spelling
Redwood is offline   Reply With Quote
Old 09-15-2009, 12:18 PM   #10787
Tech Regular
 
Join Date: Jul 2008
Posts: 286
Default setup !

Here is a link of the Setup I used to win the 13.5 rubber class at the recent IIC

http://67.199.85.166/racing/setups/t...t_iic_2009.pdf
__________________
Keven Hebert

AE / Reedy / ApexRCproshop
Futaba / BSR tires / Protoform / CR Graphics / Total-RC / ProSpec / Leespeed / 2mm designs
Keven H is offline   Reply With Quote
Old 09-15-2009, 12:33 PM   #10788
Tech Master
 
Verndog's Avatar
R/C Tech Elite Subscriber
 
Join Date: Jun 2007
Location: PPDBillet.com USA
Posts: 1,845
Trader Rating: 16 (100%+)
Default

Quote:
Originally Posted by Keven H View Post
Here is a link of the Setup I used to win the 13.5 rubber class at the recent IIC

http://67.199.85.166/racing/setups/t...t_iic_2009.pdf
Excellent job and congrats on the HUGE win Keven!

1 question on the notes, it says "Full Stiff".

I'll assume this is not just a morning condition and possibly the top deck was run without orings (locked) along with hard plastic parts??

Thanks.
Kevin
__________________
--->Dial-a-Grip for TC6
Kevin -- PPDBillet---TC6---Exoray 008
---Team Hoarders---
Verndog is offline   Reply With Quote
Old 09-15-2009, 12:53 PM   #10789
Tech Regular
 
Join Date: Jul 2008
Posts: 286
Default

Hi Kevin,

Yes full stiff means that I did not run any oring and ran all stiff parts but still ITF bottom and top plate. by the way i am still using your lipo plate !

Thanks
Keven
__________________
Keven Hebert

AE / Reedy / ApexRCproshop
Futaba / BSR tires / Protoform / CR Graphics / Total-RC / ProSpec / Leespeed / 2mm designs
Keven H is offline   Reply With Quote
Old 09-15-2009, 01:25 PM   #10790
Tech Master
 
HB Moose's Avatar
 
Join Date: Oct 2003
Location: Surf City, USA
Posts: 1,080
Default

Thanks for the help at IIC Keven. I drove the main better than I had the qualifiers. I won my F-main going away.
__________________
Bruce "Moose" Riedinger
HB Moose is offline   Reply With Quote
Old 09-15-2009, 03:42 PM   #10791
Super Moderator
 
Kraig's Avatar
 
Join Date: Aug 2001
Location: Sun Prairie, WI
Posts: 6,486
Trader Rating: 71 (100%+)
Default

Keven, I noticed you have your servo setup a little different than the factory settings. What have you noticed with this change in positioning?

Congrats on your win!
__________________
There is great need for a sarcasm font.

You never know when it will strike, but there comes a moment at work when you know that you just aren't going to do anything productive for the rest of the day.

Sometimes I post just to look at my avatar.
Kraig is offline   Reply With Quote
Old 09-15-2009, 04:33 PM   #10792
Tech Regular
 
hollywood tc5's Avatar
 
Join Date: Jul 2009
Location: Easton
Posts: 319
Trader Rating: 3 (100%+)
Default

how do you make this bulk heads that move your motor in. you just sand the bulk head
__________________
BOSS MOTORSPORTS

wrecking ball,sox,hollywood

BOSS MOTORSPORTS
hollywood tc5 is offline   Reply With Quote
Old 09-15-2009, 04:37 PM   #10793
Tech Champion
 
Join Date: Oct 2005
Location: Cincinnati, OH
Posts: 5,360
Trader Rating: 38 (100%+)
Default

Quote:
Originally Posted by hollywood tc5 View Post
how do you make this bulk heads that move your motor in. you just sand the bulk head
Im not sure what you are asking. You buy the bulkheads that move the motor in but you have to sand both the upper and lower chassis to get the motor to fit with them.
or8ital is offline   Reply With Quote
Old 09-15-2009, 04:37 PM   #10794
Suspended
 
Join Date: Apr 2008
Location: The Black Country, England
Posts: 340
Default

Quote:
Originally Posted by hollywood tc5 View Post
how do you make this bulk heads that move your motor in. you just sand the bulk head


No, you purchase a set of these bulkheads designed and made by my friend Greig Billingham (leg Iron on here)

To contact him, use either of the following e-mail addresses

[email protected]

[email protected]

__________________
It's frightening to think that with modern medicine and all technique available to them, they can’t really help you; I should think in the old days you know you were better auf, because nowadays they’re all specialists, everyone’s becoming better and better at less and less! And eventually someone’s gonna to be superb, AT NOTHING!
Nick Priest is offline   Reply With Quote
Old 09-15-2009, 05:29 PM   #10795
Tech Regular
 
hollywood tc5's Avatar
 
Join Date: Jul 2009
Location: Easton
Posts: 319
Trader Rating: 3 (100%+)
Default

Quote:
Originally Posted by Nick Priest View Post
No, you purchase a set of these bulkheads designed and made by my friend Greig Billingham (leg Iron on here)

To contact him, use either of the following e-mail addresses

[email protected]

[email protected]

o than you use the stock motor mount
__________________
BOSS MOTORSPORTS

wrecking ball,sox,hollywood

BOSS MOTORSPORTS
hollywood tc5 is offline   Reply With Quote
Old 09-15-2009, 05:48 PM   #10796
Tech Elite
 
revo61's Avatar
 
Join Date: Jun 2006
Location: In the dirty south
Posts: 2,877
Trader Rating: 18 (95%+)
Default

No the motor mount and the stock bulkheads are gone and replaced by the 2 parts you see here. If you look at the front of the longer one you will see where the motor goes.
Quote:
Originally Posted by hollywood tc5 View Post
o than you use the stock motor mount
__________________
JQ The Car Black Edition/Reds R7E/Reds 2113 pipe
Airtronics MT44/Savox servos
Sidewinder Team Strike V2 30%
USA.JQRACING.COM / WWW.NEMORACINGUSA.COM
revo61 is offline   Reply With Quote
Old 09-15-2009, 05:49 PM   #10797
Tech Master
 
beta bob's Avatar
 
Join Date: Mar 2007
Posts: 1,101
Trader Rating: 2 (75%+)
Default

Hey guys does the exotek lipo chassis work well with the tc5
__________________
Team Terribles---------2009 post of the year
"Cant you read Mopar???He said that he drives a T-max 2.5!!!!"
Spec classes are for communist
beta bob is offline   Reply With Quote
Old 09-15-2009, 06:00 PM   #10798
Tech Regular
 
hollywood tc5's Avatar
 
Join Date: Jul 2009
Location: Easton
Posts: 319
Trader Rating: 3 (100%+)
Default

o alright this helps the balence right
__________________
BOSS MOTORSPORTS

wrecking ball,sox,hollywood

BOSS MOTORSPORTS
hollywood tc5 is offline   Reply With Quote
Old 09-15-2009, 06:19 PM   #10799
Tech Champion
 
geeunit1014's Avatar
 
Join Date: Sep 2005
Location: The dirty burnie
Posts: 5,505
Trader Rating: 12 (100%+)
Default

Quote:
Originally Posted by beta bob View Post
Hey guys does the exotek lipo chassis work well with the tc5
It works extremely well for rubber tires
__________________
Mike Gee

Awesomatix USA/Pyscho Cells Racing/Tekin/Sweep Racing/RSD/180 Raceway/Johns Mobile Raceway/TQ Wire/Avid/Sanwa
geeunit1014 is offline   Reply With Quote
Old 09-15-2009, 06:21 PM   #10800
Suspended
 
Join Date: Apr 2008
Location: The Black Country, England
Posts: 340
Default

Quote:
Originally Posted by hollywood tc5 View Post
o alright this helps the balence right


Yes, it helps massively with the balance of the car.
__________________
It's frightening to think that with modern medicine and all technique available to them, they can’t really help you; I should think in the old days you know you were better auf, because nowadays they’re all specialists, everyone’s becoming better and better at less and less! And eventually someone’s gonna to be superb, AT NOTHING!
Nick Priest is offline   Reply With Quote
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
FS: Team Losi XXXS G+ with parts!! Team Orion V2 Hitec 5625 cola R/C Items: For Sale/Trade 9 06-18-2008 08:11 PM
BATTERIES - Team Orion 4200 SHO Team Cells (6 cell) packs................... For Sale 2-Bad Australia For Sale/Trade 0 03-21-2008 02:16 AM
New Items for Sale Tamiya F103gt Chassis Kit, Team Much More CTX-D, Novak, Team Orion Tsquare R/C Items: For Sale/Trade 14 04-17-2007 08:29 PM
>>> BRAND STINKING NEW NEVER RAN TEAM JAMMIN FACTORY TEAM FTE RACING BUGGY <<<< mach51 R/C Items: For Sale/Trade 5 01-25-2007 09:13 PM
F/S Team Associated Factory Team RC18T with Mamba Comp X Brushless and Extras ZeroCool101 R/C Items: For Sale/Trade 7 01-07-2006 01:54 PM



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 08:06 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net