Team Associated RC10 B5m Mid-Motor & Rear Motor Thread
|
|||
#9541
Tech Addict
iTrader: (32)
The B5m is awesome right out of the box with little setup changes needed for stock class. It is a lot better quality than the centro and way better than the B4.2. Parts are avalible at my hobby shops locally. We had a big race this last weekend and did not see any of the B series buggies break and they did great
Last edited by Tony Rivas; 05-09-2014 at 11:19 AM.
#9544
I'm having problems accelerating thru a couple of turns and dumping over the rear , any suggestions on how to cure this . the setup is pretty out of the box except 1.6 all around and White springs all around . thnx in advance
#9545
Just checking... Did you use Tamiya PS or TS paint. TS says for plastic on the can. TS will begin to flake and peel in short order.
Not saying you didn't use PS paint but it has happened to a few people I know.... In a hurry, I grabbed a can of TS paint recently from the Hobby Shop myself but caught the error before using it. Exchanged it for PS on the next trip to the shop.
Not saying you didn't use PS paint but it has happened to a few people I know.... In a hurry, I grabbed a can of TS paint recently from the Hobby Shop myself but caught the error before using it. Exchanged it for PS on the next trip to the shop.
Sure enough, just looked at the cans and two of the three I bought were TS and not PS! They were all in the same rack so I didn't even bother to look at the cans. The two colors that are peeling were the TS colors. Grr...
I wonder how hard it would be to strip the paint and start over?
Thanks for the tip! I probably would have never bothered to look at the cans again otherwise.
#9546
Hi guys are the titanium axels from Psm with it? They are only 20$ and it will drop tons of weight?
#9547
Tech Prophet
iTrader: (84)
+1 on durability. I went a little wide on a long jump landing and hit a pipe nail at full speed. The car instantly stopped, so the front arm took all of the force. I actually have a dent in my arm, but nothing broke. I broke a bulkhead going full speed into a wall....the car is not weak. And yeah,Matt. I pretty much ended up with my b4 setup with a little extra droop. If I can toon my own car, I would expect sponsored drivers to not use that as a reason to not run a chassis.
#9549
Tech Champion
iTrader: (170)
+1 on durability. I went a little wide on a long jump landing and hit a pipe nail at full speed. The car instantly stopped, so the front arm took all of the force. I actually have a dent in my arm, but nothing broke. I broke a bulkhead going full speed into a wall....the car is not weak. And yeah,Matt. I pretty much ended up with my b4 setup with a little extra droop. If I can toon my own car, I would expect sponsored drivers to not use that as a reason to not run a chassis.
http://www.rctech.net/forum/r-c-item...5-00-firm.html
#9550
Broke the front tower on pack 7...
I was punchN it over the jump with a team mate
and I got the worst if it.
silent hunter,my appoligies...
Your decorum is on a 8th grade level at best...
Try to be more friendly & respectful and maybe we could have many meaningful conversations....
#9551
Front axle weights:
Stock -
Lunsford Ti -
Exotech Ti -
??
Stock -
Lunsford Ti -
Exotech Ti -
??
#9552
Tech Master
iTrader: (12)
Ah, I needed a good laugh this morning. Can always count on RC Tech to come through in the clutch.
Anyways, currently building my MM car. I've built a lot of cars and usually take my time shaving off extra molding and whatnot. I literally had 70% of the car built in about an hour. It shows how much effort went into the fitment of parts with this car during development. Goes together so well and super quick.
Be running it soon.
TK
Anyways, currently building my MM car. I've built a lot of cars and usually take my time shaving off extra molding and whatnot. I literally had 70% of the car built in about an hour. It shows how much effort went into the fitment of parts with this car during development. Goes together so well and super quick.
Be running it soon.
TK
#9553
Tech Addict
iTrader: (18)
Started my build last night. Should I go straight to the flat arms/tower from the start or run the stock front end first? A couple guys at one track I go to have made the switch and seem to like it.
Setting up my mid so I can run it back to back with my rear motor for a while.
Setting up my mid so I can run it back to back with my rear motor for a while.
#9554
Tech Prophet
iTrader: (84)
Started my build last night. Should I go straight to the flat arms/tower from the start or run the stock front end first? A couple guys at one track I go to have made the switch and seem to like it.
Setting up my mid so I can run it back to back with my rear motor for a while.
Setting up my mid so I can run it back to back with my rear motor for a while.
#9555
Started my build last night. Should I go straight to the flat arms/tower from the start or run the stock front end first? A couple guys at one track I go to have made the switch and seem to like it.
Setting up my mid so I can run it back to back with my rear motor for a while.
Setting up my mid so I can run it back to back with my rear motor for a while.