Team Associated RC10 B5m Mid-Motor & Rear Motor Thread
|
|||
#6706
Evo
Appears the servo is to big for the car.
Appears the servo is to big for the car.
#6709
Tech Master
#6711
Sorry Evo
Those black spacers are hard for me to see on the image, just remove them .
Those black spacers are hard for me to see on the image, just remove them .
#6712
Tech Master
iTrader: (44)
he is a pretty good racer from out of town. he knew there was a different tower and it is in stock at our track but did it anyway and liked it. i guess when the ryan's do it maybe then people will try it and might like it. I dunno. he said ride height was good and used the same hole up top also. he got 2nd in expert mod at a track he only raced a couple times, first place was one of our regular experts.
From what my eyes see, "The Ryan's" were not running a B5m tower w/ flat arms at Cactus. They have the correct B5-RM tower to go with the flat arms. The AE setup sheet that NeoBuggy released, as well as the pics of Maifield's B5m reflect this. Check out the pics.
See the differences of the two towers in this post: http://www.rctech.net/forum/13109427-post2362.html
Last edited by rigor; 03-20-2014 at 02:55 PM.
#6713
So far out of the few carbon straps made the Associated strap has the most style in my opinion
#6715
I think you're mistaken?
From what my eyes see, "The Ryan's" were not running a B5-RM tower w/ flat arms at Cactus. They have the correct B5-RM tower to go with the flat arms. The AE setup sheet that NeoBuggy released, as well as the pics of Maifield's B5m reflect this. Check out the pics.
See the differences of the two towers in this post: http://www.rctech.net/forum/13109427-post2362.html
From what my eyes see, "The Ryan's" were not running a B5-RM tower w/ flat arms at Cactus. They have the correct B5-RM tower to go with the flat arms. The AE setup sheet that NeoBuggy released, as well as the pics of Maifield's B5m reflect this. Check out the pics.
See the differences of the two towers in this post: http://www.rctech.net/forum/13109427-post2362.html
They weren't running a B5-RM tower with flat arms, they were running a B5-RM tower with flat arms.
#6716
Tech Addict
iTrader: (2)
You need to start a blog or your own website or something, that way you can share your "teamates" info with people that actually care about what you and your "teamates" run. 9/10 times your posts and the drama that follows them, turns AE threads into jokes.
In one post you go on to say how you don't run 3 pad slippers, and you say the VTS is for low traction tracks....and you always rave about how TRCR is "ultra high bite" but....then you go off and say your "teamates" all run the VTS?!!
pass whatever it is you smoke, cuz it's some good ish!!
Stuff like that, (hypocritical, contradictory, erroneous info) is what ruins the AE threads...and it almost always seems to come from you!!
In one post you go on to say how you don't run 3 pad slippers, and you say the VTS is for low traction tracks....and you always rave about how TRCR is "ultra high bite" but....then you go off and say your "teamates" all run the VTS?!!
pass whatever it is you smoke, cuz it's some good ish!!
Stuff like that, (hypocritical, contradictory, erroneous info) is what ruins the AE threads...and it almost always seems to come from you!!
#6717
Everyone needs to stop jumping on the bandwagon of "hating" and making snide comments about wild cherry. He has good info to share here. He makes these threads more useful unlike all these people talking non sense about him. (Btw I do not know cherry) let's have fun racing the b5 and share good info
#6718
Tech Adept
Fellas quick build tip that I caught on my buggy n a friends........pg14 Bag J step1. Double check that u need the ballstud washer!! (1mm) For some servos if u install it, it will pull the steering link to close to the servo n limit steering or bind to the right!! Most will finish the build, then set end points on the bench n make the endpoint at the point where the link contacts the servo body if u do that u will lose a good amount of steering to the right!!! Don't use the washer n with a xacto knife cut a little material off the link so it can pass smooth right next to the servo.....n you will have full throw! Anyone complaining of poor steering prob has the washer installed
#6719
#6720
Tech Regular
iTrader: (6)
I think you're mistaken?
From what my eyes see, "The Ryan's" were not running a B5-RM tower w/ flat arms at Cactus. They have the correct B5-RM tower to go with the flat arms. The AE setup sheet that NeoBuggy released, as well as the pics of Maifield's B5m reflect this. Check out the pics.
See the differences of the two towers in this post: http://www.rctech.net/forum/13109427-post2362.html
From what my eyes see, "The Ryan's" were not running a B5-RM tower w/ flat arms at Cactus. They have the correct B5-RM tower to go with the flat arms. The AE setup sheet that NeoBuggy released, as well as the pics of Maifield's B5m reflect this. Check out the pics.
See the differences of the two towers in this post: http://www.rctech.net/forum/13109427-post2362.html
I guess it went over your head, Point being evrything the pro's do people who don't have their talent will try. kinda like all the crying over cactus setups, who races a sugared outdoor track weekly???
It cracks me up that i say a guy i race with did it and liked it , and you keep saying it won't work cause sean said so...lol
And i am also racing a b5m on a low traction track, but it won't work for that either,right?