137LikesTeam Associated RC10 B5m Mid-Motor & Rear Motor Thread
04-22-2024, 12:09 PM - Wikipost
|
|||
|
|||
|
02-11-2014, 08:57 AM
#3155
Tech Master
Tower, Superior and Amain are all out. Best to check local shops.
02-11-2014, 09:06 AM
#3157
I searched B5 Silencer and got no results...looked through all of the 1/10 bodies and didn't see anything there either. Tower says they expect it mid Feb and AMain doesn't have anything.Where do I get one...I ruined my kit body.
02-11-2014, 09:08 AM
#3158
And yet it isn't even on the Jcon site. I searched B5 Silencer and got no results...looked through all of the 1/10 bodies and didn't see anything there either. Tower says they expect it mid Feb and AMain doesn't have anything.
Where do I get one...I ruined my kit body.
I searched B5 Silencer and got no results...looked through all of the 1/10 bodies and didn't see anything there either. Tower says they expect it mid Feb and AMain doesn't have anything.Where do I get one...I ruined my kit body.
02-11-2014, 09:11 AM
#3159
Servo fitment issues?
I went to install my Airtronics 94780 servo and it didn't fit. The front would hit the steering arm and I couldn't move it back because of the cross bar. Since that didn't fit I removed the Savox SC1251MG from my 6.1 and that wouldn't fit in the B5 because the aluminum servo mount was too long and the wires coming out of the servo were in the way. So being in a time crunch I installed a Hitec 645MG I had lying around because it was the only one that would fit out of what I had. I couldn't run the servo wires in the tunnel down the center of the chassis because they wouldn't fit without being crushed by the servo. Then I went to the track and blew all the corners because the servo is so slow.
*So what servos are y'all using? I want to buy one that I know will fit. Any help will be much appreciated.
*So what servos are y'all using? I want to buy one that I know will fit. Any help will be much appreciated.
02-11-2014, 09:13 AM
#3160
I went to install my Airtronics 94780 servo and it didn't fit. The front would hit the steering arm and I couldn't move it back because of the cross bar. Since that didn't fit I removed the Savox SC1251MG from my 6.1 and that wouldn't fit in the B5 because the aluminum servo mount was too long and the wires coming out of the servo were in the way. So being in a time crunch I installed a Hitec 645MG I had lying around because it was the only one that would fit out of what I had. I couldn't run the servo wires in the tunnel down the center of the chassis because they wouldn't fit without being crushed by the servo. Then I went to the track and blew all the corners because the servo is so slow.
*So what servos are y'all using? I want to buy one that I know will fit. Any help will be much appreciated.
*So what servos are y'all using? I want to buy one that I know will fit. Any help will be much appreciated.
XP 1015 fit too but I had shortened the wire and it didn't reach the rx in the back of the car.
02-11-2014, 09:21 AM
#3163
I went to install my Airtronics 94780 servo and it didn't fit. The front would hit the steering arm and I couldn't move it back because of the cross bar. Since that didn't fit I removed the Savox SC1251MG from my 6.1 and that wouldn't fit in the B5 because the aluminum servo mount was too long and the wires coming out of the servo were in the way. So being in a time crunch I installed a Hitec 645MG I had lying around because it was the only one that would fit out of what I had. I couldn't run the servo wires in the tunnel down the center of the chassis because they wouldn't fit without being crushed by the servo. Then I went to the track and blew all the corners because the servo is so slow.
*So what servos are y'all using? I want to buy one that I know will fit. Any help will be much appreciated.
*So what servos are y'all using? I want to buy one that I know will fit. Any help will be much appreciated.