137LikesTeam Associated RC10 B5m Mid-Motor & Rear Motor Thread
04-22-2024, 12:09 PM - Wikipost
|
|||
|
|||
|
10-26-2014, 10:00 AM
Tech Master
iTrader: (8)
have any of you guys tried the xfactory carbon fiber chassis ?
10-26-2014, 10:31 AM
Tech Apprentice
Just putmy B5 together, had a day at the track.. great and smootto drive..
im getting different opinions on upgrade parts.. one guy says to put aluminium on , the next says to just buy theoriginal plastics when the need replacement..
I am running on a hard clay track.. carpet track soom...
im getting different opinions on upgrade parts.. one guy says to put aluminium on , the next says to just buy theoriginal plastics when the need replacement..
I am running on a hard clay track.. carpet track soom...
10-26-2014, 01:57 PM
Tech Regular
iTrader: (36)
Mod guy here, who will be running 17.5 for a large race in our area (Spektrum Champs @trackside hobbies).
Curious if anyone has had any experience with the following shorty lipo. I hear the SMC packs are great, but they aren't due for another month
Other suggestions welcome.
https://www.aero-model.com/4_159_269...0-2S90PRO.html
Curious if anyone has had any experience with the following shorty lipo. I hear the SMC packs are great, but they aren't due for another month
Other suggestions welcome.
https://www.aero-model.com/4_159_269...0-2S90PRO.html
10-26-2014, 03:08 PM
Tech Rookie
Anyone have a specific motor recommendation for indoor clay short track, 17.5t?
10-26-2014, 03:10 PM
Tech Rookie
What size shorty are you guys running on short track 17.5?
10-26-2014, 03:37 PM
10-26-2014, 03:38 PM
10-26-2014, 05:04 PM
There is one at the track I race at. Looks really good. Problem: the car comes in underweight. My pit buddy drove it and he said it is much more forgiving than his stock B5m. My 2 cents.
10-26-2014, 05:41 PM
Tech Adept
measuring ride height
Where do you take that measurement from? With the gullwing it is difficult to see flat and level.
10-26-2014, 08:40 PM
Tech Rookie
10-26-2014, 09:34 PM
10-26-2014, 09:50 PM
Anyone had problems with bent hinge pins?
Was rebuilding my car, and noticed that my rear hinge pins (the one is very very slightly bent) but the other is diffidently bent. Same with shock shaft (opposite side)... Little irritated but guess it's my own fault.
Was rebuilding my car, and noticed that my rear hinge pins (the one is very very slightly bent) but the other is diffidently bent. Same with shock shaft (opposite side)... Little irritated but guess it's my own fault.
10-26-2014, 10:33 PM
Tech Fanatic
iTrader: (1)
Does anyone know how much weight a Ti screw kit will take off the chassis? or should I go for the Team aluminium kit?
10-26-2014, 10:38 PM
Not sure on rm but on the mid motor it cuts about 20 grams
10-27-2014, 12:08 AM
Tech Fanatic
iTrader: (1)
Seems like a worthy weight saving! Esp if I'm going to try use a brass front hinge block.
Edit: is it actually work getting the brass block to improve the steering and stop the car from pushing? I've gotten used to my MM Firebolt and trying to tune the RM B5 to see if I can get similar lap times on medium hard pack.
Edit: is it actually work getting the brass block to improve the steering and stop the car from pushing? I've gotten used to my MM Firebolt and trying to tune the RM B5 to see if I can get similar lap times on medium hard pack.
Last edited by WagwanBumba; 10-27-2014 at 12:26 AM.