Go Back  R/C Tech Forums > General Forums > Electric Off-Road
Team Associated RC10 B5 Rear-Motor Thread >

Team Associated RC10 B5 Rear-Motor Thread

Like Tree32Likes

Team Associated RC10 B5 Rear-Motor Thread

Reply

Old 08-11-2014, 12:51 PM
  #6256  
CnR
Tech Addict
iTrader: (31)
 
CnR's Avatar
 
Join Date: Apr 2012
Posts: 652
Trader Rating: 31 (100%+)
Default

I know this is me being lazy but can someone upload a setup sheet with the latest standard setup. I keep hearing using different arms and such. It would be greatly appreciated. In the mean time I will try and dig through the thread and get one filled out. I am an engineer I don't like to read just see pictures. ;-)
CnR is offline  
Reply With Quote
Old 08-12-2014, 03:42 PM
  #6257  
Tech Elite
iTrader: (152)
 
Join Date: Aug 2010
Location: Vancouver, Washington
Posts: 4,305
Trader Rating: 152 (100%+)
Default

Originally Posted by Wildcat1971 View Post
yeah, its 4mm. Really wish someone made a 5mm version.
It doesn't make much sense since all of their other 90c packs have the 5mm bullets.
jpcopeland1 is offline  
Reply With Quote
Old 08-12-2014, 05:28 PM
  #6258  
Tech Prophet
iTrader: (82)
 
Wildcat1971's Avatar
 
Join Date: Apr 2012
Location: Arizona
Posts: 17,229
Trader Rating: 82 (100%+)
Default

Originally Posted by jpcopeland1 View Post
It doesn't make much sense since all of their other 90c packs have the 5mm bullets.
yeah, I converted my stuff to 5mm. No biggie to go back, just like all my packs to use the same bullets
Wildcat1971 is online now  
Reply With Quote
Old 08-12-2014, 05:44 PM
  #6259  
Tech Elite
iTrader: (152)
 
Join Date: Aug 2010
Location: Vancouver, Washington
Posts: 4,305
Trader Rating: 152 (100%+)
Default

Originally Posted by Wildcat1971 View Post
yeah, I converted my stuff to 5mm. No biggie to go back, just like all my packs to use the same bullets
I know what you mean. When I had my short course truck I used full sized packs with 5mm bullets. Was not a big deal as I just wired up a new change harness with a 5mm bullet. But it got tedious switching back and forth from 4mm harness to 5mm harness then back again.
jpcopeland1 is offline  
Reply With Quote
Old 08-12-2014, 05:53 PM
  #6260  
Tech Master
iTrader: (5)
 
Join Date: May 2010
Location: Gaylord,MI and Owosso,MI
Posts: 1,098
Trader Rating: 5 (100%+)
Default

i have a couple more questions. roll center, what is it and what is the purpose? if i change the trailing arms inserts what will it do to the car? and what will rear toe do to the car?
bbrace3m is offline  
Reply With Quote
Old 08-12-2014, 06:45 PM
  #6261  
Tech Elite
iTrader: (222)
 
Join Date: Jul 2009
Location: Cadillac, MI
Posts: 3,252
Trader Rating: 222 (100%+)
Default

Originally Posted by bbrace3m View Post
i have a couple more questions. roll center, what is it and what is the purpose? if i change the trailing arms inserts what will it do to the car? and what will rear toe do to the car?
I even printed this for you last time we raced. Everything you need to know is here

http://www.competitionx.com/rc-racing/rc-tuning-guide/
Manatarms25 is offline  
Reply With Quote
Old 08-12-2014, 06:53 PM
  #6262  
Suspended
iTrader: (12)
 
Join Date: Aug 2010
Posts: 1,990
Trader Rating: 12 (100%+)
Default

Originally Posted by Manatarms25 View Post
I even printed this for you last time we raced. Everything you need to know is here

http://www.competitionx.com/rc-racing/rc-tuning-guide/
You should have read it to him and showed pictures
PFKAOG is offline  
Reply With Quote
Old 08-12-2014, 07:34 PM
  #6263  
Tech Elite
iTrader: (152)
 
Join Date: Aug 2010
Location: Vancouver, Washington
Posts: 4,305
Trader Rating: 152 (100%+)
Default

Originally Posted by PFKAOG View Post
You should have read it to him and showed pictures
+1 hehe..
jpcopeland1 is offline  
Reply With Quote
Old 08-13-2014, 08:48 AM
  #6264  
Tech Master
iTrader: (5)
 
Join Date: May 2010
Location: Gaylord,MI and Owosso,MI
Posts: 1,098
Trader Rating: 5 (100%+)
Default

Its called not being able to find it in my stack of college books. Lol. I got it now though. I'm gonna do a base set up from a sheet on AE website and go from there.
bbrace3m is offline  
Reply With Quote
Old 08-13-2014, 08:54 AM
  #6265  
Tech Fanatic
iTrader: (48)
 
vwduud's Avatar
 
Join Date: Apr 2010
Location: Prairieville, LA
Posts: 959
Trader Rating: 48 (100%+)
Default

Originally Posted by bbrace3m View Post
i have a couple more questions. roll center, what is it and what is the purpose? if i change the trailing arms inserts what will it do to the car? and what will rear toe do to the car?
Some tools that have I used (and still use) to learn and apply the effects of Roll Center:

http://thecartech.com/subjects/auto_...oll_Center.htm

The above link does a good job of explaining the geometry and calculation of Roll Center in very basic terms with diagrams.

Now, if you want to further that knowledge as it applies to your specific chassis, check out RC Crew Chief:

http://www.rccrewchief.wrightdesign.ca/Index.aspx

RC Crew Chief is a software tool used to model the chassis's suspension system. Once your model is in the software, you're able to make virtual changes to your suspension to see what those changes affect in terms of performance (push, loose, chassis roll sensitivity, etc.). You can see "where" the front and rear Roll Centers are. If you have a slight push, off power, you can make a virtual change in the software (change a camber link position, for example) to pre-determine the physical change you actually make on your car to overcome that push.

Another benefit includes choosing a good front to rear spring combination. In addition to Roll Center, "Ride Frequency" is another quality found in sprung suspension systems. Take the guess work out of what front springs will work well with the chosen rears. Take the guess work out of the "fine-tuning" of the springs by moving the shock mounting positions on the towers and suspension arms.

Anti Roll Bars are included in the calculations. See what changing the ARB will do before actually changing it.

Very powerful software. I've been using it on both my 1/8 Tekno eBuggy and the AE B5 with impressive results over the past 9 months. Beats the "seat of the pants" method of figuring out what changes we need to make on these complicated racing chassis's.

Feel free to PM me with any questions on the use of this software. While not overly difficult, there is a learning curve in both measuring your car (to get the information into the software) as well as knowing what you're looking for and how to go about setting your car up.

Jim
vwduud is offline  
Reply With Quote
Old 08-14-2014, 02:51 PM
  #6266  
Tech Rookie
 
Join Date: Aug 2014
Location: Phoenix, Arizona
Posts: 8
Default

This is great! It applies to both on and off-road setups. I'm going to try and build my B5 tomorrow (no guarantees), I'll post some photos.
Buggy Buddy is offline  
Reply With Quote
Old 08-15-2014, 12:07 PM
  #6267  
Tech Master
iTrader: (62)
 
BRSracing's Avatar
 
Join Date: Mar 2011
Location: Blue Springs MO
Posts: 1,765
Trader Rating: 62 (100%+)
Default

For the past few months I have been running the mid motor, with very mixed results. Ran my friends rear motor a few nights ago and liked it much better. Am I the only one going from mid to rear? Seems like its the other way around.
BRSracing is offline  
Reply With Quote
Old 08-15-2014, 02:00 PM
  #6268  
Tech Prophet
iTrader: (82)
 
Wildcat1971's Avatar
 
Join Date: Apr 2012
Location: Arizona
Posts: 17,229
Trader Rating: 82 (100%+)
Default

Originally Posted by BRSracing View Post
For the past few months I have been running the mid motor, with very mixed results. Ran my friends rear motor a few nights ago and liked it much better. Am I the only one going from mid to rear? Seems like its the other way around.
I get mixed results also. I have the conversion, so I can go back to RM fairly easily. I am giving the MM a little more time. It drives well, but my consistency when I really need it, falls short. I am still learning how to push the car and keep it from stepping out. The RM much more planted in the rear and provided more confidence. I am hoping the MM is just a learning curve.
Wildcat1971 is online now  
Reply With Quote
Old 08-15-2014, 03:07 PM
  #6269  
Tech Elite
iTrader: (209)
 
hlpressley's Avatar
 
Join Date: Dec 2007
Location: Charlotte, NC
Posts: 2,716
Trader Rating: 209 (99%+)
Default

Anyone running the brass front bulkhead? Just got mine in today, hoping it will help the car turn a little better on power.
hlpressley is offline  
Reply With Quote
Old 08-15-2014, 03:15 PM
  #6270  
Tech Prophet
iTrader: (82)
 
Wildcat1971's Avatar
 
Join Date: Apr 2012
Location: Arizona
Posts: 17,229
Trader Rating: 82 (100%+)
Default

Well it will keep the front down acceleration
Wildcat1971 is online now  
Reply With Quote

Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service