Xray XB4 thread
Tech Master
iTrader: (36)
Anyone running these Turnigy packs? I am running mod 4wd outdoors so thinking I don't need high end batteries like the Orions
http://www.hobbyking.com/hobbyking/s...arehouse_.html
or for a little more
http://www.hobbyking.com/hobbyking/s...arehouse_.html
http://www.hobbyking.com/hobbyking/s...arehouse_.html
or for a little more
http://www.hobbyking.com/hobbyking/s...arehouse_.html
GTG. But keep in mind the more expensive one uses 5mm plugs not the normal 4mm, so pick up extra of those.
Tech Elite
iTrader: (33)
Anyone running these Turnigy packs? I am running mod 4wd outdoors so thinking I don't need high end batteries like the Orions
http://www.hobbyking.com/hobbyking/s...arehouse_.html
or for a little more
http://www.hobbyking.com/hobbyking/s...arehouse_.html
http://www.hobbyking.com/hobbyking/s...arehouse_.html
or for a little more
http://www.hobbyking.com/hobbyking/s...arehouse_.html
Tech Champion
iTrader: (515)
I've been using the Fantom 100c lipos lately and they are pretty good. The Protek 100c w/5mm are good too. Neither too expensive.
Where the market for these? Been trying to sell mine for awhile now, not much interest.
Tech Addict
iTrader: (11)
Ive been using the older and newer ultra orion shortys. they are only $59 bucks and they last for ever. I still have my 1st set from when i bought the 15spec and I would have no issue using them in a A-Main with over 70 runs on it.
Tech Champion
iTrader: (259)
Tech Fanatic
iTrader: (15)
what are ya'll running for motors/gearing?
Im running a 5.5t motor with 18/81.
People have been saying that might be geared a little high. would it be smarter to go with 19 / 84?
Im running a 5.5t motor with 18/81.
People have been saying that might be geared a little high. would it be smarter to go with 19 / 84?
Tech Master
iTrader: (10)
Im curious on gearing for a 5.5 also, with my 6.5 I was running 20/81. I was going to put a 19 on to start but am not sure.
Found a setup-sheet created for XB4 -15, is there anything special I should consider when I use it to my -16?
Tech Elite
iTrader: (33)
Tech Addict
iTrader: (11)
I had a Orion r10.1 with my orion 6.5 all winter and put the orion 5.5t in since we are now outdoors and on bigger tracks. I started with a 18 tooth pinion and after a full pack my motor wasnt even hot, I didnt temp it but it wasnt warmer then a truck hood would be for a example, I went up to a 19 tooth and will be running that for now on. so 19/81 on a 5.5t and I am 100% sure I would have no issue with a 20 maybe even a 21 if needed but I would never need that much and we have a big track here (710 raceway).
Tech Fanatic
iTrader: (15)
I had a Orion r10.1 with my orion 6.5 all winter and put the orion 5.5t in since we are now outdoors and on bigger tracks. I started with a 18 tooth pinion and after a full pack my motor wasnt even hot, I didnt temp it but it wasnt warmer then a truck hood would be for a example, I went up to a 19 tooth and will be running that for now on. so 19/81 on a 5.5t and I am 100% sure I would have no issue with a 20 maybe even a 21 if needed but I would never need that much and we have a big track here (710 raceway).
Tech Champion
iTrader: (14)
It depends on the track size and more specifically the longest straight away. People seem to miss this important part and those guys telling you about geared too high at the track may be right.
Tech Fanatic
iTrader: (15)
im speaking strictly in like motor safety/general driveability. not necessarily optimizing per track. my 18t seems fine on mid sized tracks.