Go Back  R/C Tech Forums > General Forums > Electric Off-Road
Losi 1/10 TEN-SCTE ARR 4x4 Short Course Truck Thread >

Losi 1/10 TEN-SCTE ARR 4x4 Short Course Truck Thread

Like Tree9Likes

Losi 1/10 TEN-SCTE ARR 4x4 Short Course Truck Thread

Old 07-18-2011, 09:08 PM
  #14851  
Tech Regular
iTrader: (10)
 
liftedcj7on44s's Avatar
 
Join Date: Mar 2009
Location: Fayetteville, N.C.
Posts: 486
Trader Rating: 10 (100%+)
Default

Originally Posted by RC*PHREAK
i have that same set up from when my rig was a ten-t. don't really have much need for it now.........
Send them my way! LOL


To the guy asking about the MMP and the 1410. It has been beaten to death in this thread. Most people run that setup(well a lot of them including myself).

I personally run a 15T pinion.
liftedcj7on44s is offline  
Old 07-18-2011, 09:10 PM
  #14852  
Tech Regular
iTrader: (10)
 
liftedcj7on44s's Avatar
 
Join Date: Mar 2009
Location: Fayetteville, N.C.
Posts: 486
Trader Rating: 10 (100%+)
Default

Originally Posted by SaladFork
You can cut that lip off, but it doesn't change the offset since the pin is still in the same spot. Knowing Josh, he cut that off to save weight.

Hmmm, I am no rocket scientist or an engineer but if you cut that lip off then the outer bearing will come out of the spindle.
liftedcj7on44s is offline  
Old 07-18-2011, 09:21 PM
  #14853  
Tech Master
iTrader: (37)
 
Mr.juarez's Avatar
 
Join Date: Dec 2008
Posts: 1,280
Trader Rating: 37 (100%+)
Default

Originally Posted by lowroad
no, no one.
lmfao!!!!

Originally Posted by RC*PHREAK
i have that same set up from when my rig was a ten-t. don't really have much need for it now.........
+ YouTube Video
ERROR: If you can see this, then YouTube is down or you don't have Flash installed.


Originally Posted by liftedcj7on44s
Hmmm, I am no rocket scientist or an engineer but if you cut that lip off then the outer bearing will come out of the spindle.
no it wont. you dont cut it flush but you leave that tiny little small lip for the bearing to sit on

Mr.juarez is offline  
Old 07-18-2011, 09:21 PM
  #14854  
Tech Champion
iTrader: (146)
 
RC*PHREAK's Avatar
 
Join Date: Dec 2010
Posts: 5,387
Trader Rating: 146 (100%+)
Default

Originally Posted by liftedcj7on44s
Send them my way! LOL


To the guy asking about the MMP and the 1410. It has been beaten to death in this thread. Most people run that setup(well a lot of them including myself).

I personally run a 15T pinion.
what you got to trade?

M2C 17mm adapters go for 30 and i don't know what the ten-t axles go for. let's work a little trade. doesn't even have to be equal value. like some spare parts for the SCTE? i dunno.
RC*PHREAK is offline  
Old 07-18-2011, 09:25 PM
  #14855  
Tech Master
iTrader: (37)
 
Mr.juarez's Avatar
 
Join Date: Dec 2008
Posts: 1,280
Trader Rating: 37 (100%+)
Default

Originally Posted by RC*PHREAK
what you got to trade?

M2C 17mm adapters go for 30 and i don't know what the ten-t axles go for. let's work a little trade. doesn't even have to be equal value. like some spare parts for the SCTE? i dunno.
if lifted doesnt take them i may have some things to trade you for them. like new 1 day used strc towers in blue, set of shock parts losb294, strc shock collars.
Mr.juarez is offline  
Old 07-18-2011, 09:32 PM
  #14856  
Tech Regular
iTrader: (10)
 
liftedcj7on44s's Avatar
 
Join Date: Mar 2009
Location: Fayetteville, N.C.
Posts: 486
Trader Rating: 10 (100%+)
Default

Originally Posted by RC*PHREAK
what you got to trade?

M2C 17mm adapters go for 30 and i don't know what the ten-t axles go for. let's work a little trade. doesn't even have to be equal value. like some spare parts for the SCTE? i dunno.

I got new A-arms front and rear.
liftedcj7on44s is offline  
Old 07-18-2011, 09:46 PM
  #14857  
Tech Champion
iTrader: (146)
 
RC*PHREAK's Avatar
 
Join Date: Dec 2010
Posts: 5,387
Trader Rating: 146 (100%+)
Default

Originally Posted by liftedcj7on44s
I got new A-arms front and rear.
done. mr. juarez is an honest chap and deferred to you. let's take it to PM's for details.
RC*PHREAK is offline  
Old 07-18-2011, 09:47 PM
  #14858  
Tech Champion
iTrader: (25)
 
losi_racer's Avatar
 
Join Date: Nov 2008
Location: mesa,az
Posts: 6,470
Trader Rating: 25 (100%+)
Default

Originally Posted by losi_racer
question since were on the whole run time/heat thing here : )

Im running 5.5, RX8, stock settings on the esc. I was running a 16T Pinion, i was running 180 then one night it went to 200, had to drop to a 15T now im at 155. Since then ive already tore the truck apart no binding, mesh is fine, also run time isnt an issue on either pinion. IF i drop my CL down to 80-85, this will limit the amp draw and cool the motor, so would i be able to go back up to my 16 then and my temps should be 160-170 range? I liked it better as ive lost my top end with the 15 but its not terrible. also btw im in az where its 100-105 at night when we race
losi_racer is offline  
Old 07-18-2011, 10:03 PM
  #14859  
Tech Elite
iTrader: (140)
 
timannnn6's Avatar
 
Join Date: Jul 2010
Posts: 2,285
Trader Rating: 140 (100%+)
Default

Originally Posted by BlackLabelVinyl
Hey guys, I just started making these for the Losi. Let me know if you're interested.

http://www.rctech.net/forum/r-c-item...4x4-1-8-a.html
You can get a 8 inch by 10 foot roll of 15mil for $13.99 shipped on fleabay.

http://cgi.ebay.com/ebaymotors/1-rol...#ht_500wt_1124
timannnn6 is offline  
Old 07-18-2011, 10:05 PM
  #14860  
Tech Master
iTrader: (37)
 
Mr.juarez's Avatar
 
Join Date: Dec 2008
Posts: 1,280
Trader Rating: 37 (100%+)
Default

wow! that was a low blow
Mr.juarez is offline  
Old 07-18-2011, 10:10 PM
  #14861  
Tech Regular
iTrader: (10)
 
liftedcj7on44s's Avatar
 
Join Date: Mar 2009
Location: Fayetteville, N.C.
Posts: 486
Trader Rating: 10 (100%+)
Default

Originally Posted by Mr.juarez
wow! that was a low blow

I agree.
liftedcj7on44s is offline  
Old 07-18-2011, 10:22 PM
  #14862  
Tech Adept
iTrader: (19)
 
Join Date: Jan 2009
Location: Northern VA
Posts: 178
Trader Rating: 19 (100%+)
Default Wheel Adapters!!!

Wheel Adapters...

Anything made for or used on the Ten-T or even the 810 is NOT going to work, including the Traxxas adapters for the Maxx series UNLESS you convert to the respective stub axles, either the Ten-T axles that are "0 offset" or the wider 810 axles.

The main reason is the Ten-T and 810 axle "shoulders" that support the hex's are 6mm and the through pin is larger that the SCTE's 5mm axle and pin.

What will work if you want to keep the SCTE's stock axle and pin is anything that was made for the rear on all the other sct's on the market already to convert to 17mm, although some have more offset than others.


These look perfect though if you dont want to alter the offset, although you might actually end up a little narrower than stock if using a flat faced buggy wheel.

http://www.amainhobbies.com/product_...dapters-Rear-2



The ones for the Slash 4x4 by AKA look pretty good too and should be close to 0 offset considering on the Slash 4x4 they are intended to keep the "stock" offset, although you probably will end up slightly wider...

http://www.amainhobbies.com/product_...s-Complete-Kit



I'm sure the will be specific SCTE one's on the market soon enough...

Last edited by shenri; 07-18-2011 at 10:50 PM.
shenri is offline  
Old 07-18-2011, 10:30 PM
  #14863  
Tech Regular
iTrader: (10)
 
liftedcj7on44s's Avatar
 
Join Date: Mar 2009
Location: Fayetteville, N.C.
Posts: 486
Trader Rating: 10 (100%+)
Default

Pretty sure that is why the one's that I am going to get from RC Phreak will include the Ten T stub axle.
liftedcj7on44s is offline  
Old 07-18-2011, 10:32 PM
  #14864  
Tech Champion
iTrader: (146)
 
RC*PHREAK's Avatar
 
Join Date: Dec 2010
Posts: 5,387
Trader Rating: 146 (100%+)
Default

Originally Posted by liftedcj7on44s
Pretty sure that is why the one's that I am going to get from RC Phreak will include the Ten T stub axle.
stub axles, and the larger pins (which you can see in the pictures that are in the adapters).
RC*PHREAK is offline  
Old 07-18-2011, 10:33 PM
  #14865  
Tech Master
iTrader: (37)
 
Mr.juarez's Avatar
 
Join Date: Dec 2008
Posts: 1,280
Trader Rating: 37 (100%+)
Default

Originally Posted by liftedcj7on44s
Pretty sure that is why the one's that I am going to get from RC Phreak will include the Ten T stub axle.
and less parts that you wont find when you lose them at the track im sure you got a great deal
Mr.juarez is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Your Privacy Choices -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.