Durango DEX210 Thread
#9391
sorry, was starting with the box setup WITHOUT the camber link mod from tresrey. so the ball stud is on the gear case like stock with the 2mm shim the manual started with. so that would mean to add the shim
i have the aluminum hubs on it that I took off the short course truck figuring the buggy open wheel would benefit more compared to the truck. so I have the correct amount on that already to get it lined up. now its just on to tuning to get rid of some of this on power push
i have the aluminum hubs on it that I took off the short course truck figuring the buggy open wheel would benefit more compared to the truck. so I have the correct amount on that already to get it lined up. now its just on to tuning to get rid of some of this on power push
Oh, well that is completely different. I personally wouldn't try to tune that out with the shims. IMO I would toss that setup, and trade it for something off petitrc that is on a similar surface to what u run it on. I think u will be able to tune it better from one of those setup's.
#9395
#9397
Tech Addict
iTrader: (18)
If anyone is looking for a mint 210, let me know fellas. Bind and go
http://www.rctech.net/forum/r-c-item...x210-artr.html
http://www.rctech.net/forum/r-c-item...x210-artr.html
#9398
Tech Adept
210 RTR Gear Diff
I opened up the gear diff, and noticed it only has 1 cross shaft axle with 2 small spider gears, does not look like your typical diff set up with 2 cross shaft axles with 4 small diff gears. Is this normal on RTR ? Or am I missing some parts in this diff ?
Last edited by Ramirez24; 12-26-2012 at 05:16 PM.
#9399
Tech Elite
iTrader: (88)
#9400
Tech Fanatic
iTrader: (29)
Wow. 27.5 in the rear? Any weight in the front or rear? Does the rear end roll?
I have been trying to take the roll out of the rear. It rolls then spins. Ive been trying to calm it down. Does the hevy weight oil up front help. I have 40 up front with the light brown springs and 1.3 4 hole pistons and I have 21 grams up front and I cant get it down to ride height. I to have been using this set up with some tweeks. I been trying to get high roll center in the rear. My links are all the way out and shocks lay down all the way. Tried putting 4 mm under the inner ball studs too.
I have been trying to take the roll out of the rear. It rolls then spins. Ive been trying to calm it down. Does the hevy weight oil up front help. I have 40 up front with the light brown springs and 1.3 4 hole pistons and I have 21 grams up front and I cant get it down to ride height. I to have been using this set up with some tweeks. I been trying to get high roll center in the rear. My links are all the way out and shocks lay down all the way. Tried putting 4 mm under the inner ball studs too.
Here is my setup for carpet.
http://dl.dropbox.com/u/14824938/RC%...210_Carpet.pdf
#9402
Wow. 27.5 in the rear? Any weight in the front or rear? Does the rear end roll?
I have been trying to take the roll out of the rear. It rolls then spins. Ive been trying to calm it down. Does the hevy weight oil up front help. I have 40 up front with the light brown springs and 1.3 4 hole pistons and I have 21 grams up front and I cant get it down to ride height. I to have been using this set up with some tweeks. I been trying to get high roll center in the rear. My links are all the way out and shocks lay down all the way. Tried putting 4 mm under the inner ball studs too.
I have been trying to take the roll out of the rear. It rolls then spins. Ive been trying to calm it down. Does the hevy weight oil up front help. I have 40 up front with the light brown springs and 1.3 4 hole pistons and I have 21 grams up front and I cant get it down to ride height. I to have been using this set up with some tweeks. I been trying to get high roll center in the rear. My links are all the way out and shocks lay down all the way. Tried putting 4 mm under the inner ball studs too.
I want to make it back to that carpet track some time, only with mini pins and cut staggers instead of the dirt setup I usually run.
#9404
Tech Adept
Looking at the picture on the box it looks like it only comes with 1 - if so I think you can just buy the shaft and gears as a set if you want 4. The extra gears just help take the load if you run higher torque motors than supplied
#9405