Durango DEX210 Thread
#4293
Tech Master
iTrader: (13)
Has anybody had any issues with the doodad that holds the servo mounts mating properly with the chassis wings and lining up with the holes properly?
The right side seems to mate up just fine and line up with the steering rack mount, but the holes don't line up, and the left side just doesn't line up with ANYTHING.
The right side seems to mate up just fine and line up with the steering rack mount, but the holes don't line up, and the left side just doesn't line up with ANYTHING.
#4294
I had some on-road shims from my corally that I used. There was quite a bit of play though. When I change the fluid after this weekend I will get back to you.
#4295
Have been running the car since it came out and have only broken a front shock tower. Car is awesome
#4298
Bugle boy side profile!
New improved Gearboxfix:
New improved Gearboxfix:
#4299
Tech Elite
iTrader: (42)
Join Date: Jun 2008
Location: anywhere I can race 2wd dirt,and 1/12 onroad in MI.
Posts: 3,891
Trader Rating: 42 (100%+)
Hey Mantis, are those BB shells in stock at your store???
#4300
Tech Elite
iTrader: (42)
Join Date: Jun 2008
Location: anywhere I can race 2wd dirt,and 1/12 onroad in MI.
Posts: 3,891
Trader Rating: 42 (100%+)
also you guys with noisy trannsmissions---I tore my tranny down to switch from MM3 to MM4 for running ozite.In MM3 my tranny was noisy.so I gave the trans a quick go-thru while I was at it..I noticed that the top shaft gear fit the top shaft a little sloppy..so i used some thin CA to put a thin layer of CA on the top shaft where the gear rides..just put it on and wiped it off with a rag..the gear still slid on the shaft, but way more snugly than it previously did..No more sloppy wiggle on the shaft and viola, no more noisy trannsmission when it went back together
#4301
I have them and plan on adding them to the site tonight. i did not get very many in on this run, kinda feeling the market. iI like it though!
this is where they will be:
http://rcshox.com/shoxshop/catalog/i...hp?cPath=23_31
this is where they will be:
http://rcshox.com/shoxshop/catalog/i...hp?cPath=23_31
#4302
Tech Elite
iTrader: (42)
Join Date: Jun 2008
Location: anywhere I can race 2wd dirt,and 1/12 onroad in MI.
Posts: 3,891
Trader Rating: 42 (100%+)
I have them and plan on adding them to the site tonight. i did not get very many in on this run, kinda feeling the market. iI like it though!
this is where they will be:
http://rcshox.com/shoxshop/catalog/i...hp?cPath=23_31
this is where they will be:
http://rcshox.com/shoxshop/catalog/i...hp?cPath=23_31
#4303
Tech Adept
iTrader: (5)
You will appreciate the tunability of the car. As for breakage; Jeremy and I have been running the car since its release with only a steering rack and shock eyelet for breakage. We run the TC5 ballstuds with Jason's ballcups as well as his body and rear hexes. Make the jump....you'll be glad you did!
#4304
Tech Elite
iTrader: (42)
Join Date: Jun 2008
Location: anywhere I can race 2wd dirt,and 1/12 onroad in MI.
Posts: 3,891
Trader Rating: 42 (100%+)
also just got this in the mail today..from a seller in canada,it was $15.Nice peice.Is a direct replacement for the stock 3/3 front rear toe block.