Durango DEX210 Thread
#5101
Tech Master
iTrader: (27)
Join Date: Dec 2003
Location: im 4rm a far away place called 1st
Posts: 1,849
Trader Rating: 27 (100%+)
So, I decided to slow myself down last night and raced "blinky" stock buggy to nail down a basic setup. I was really happy with how my car felt all round except for one thing... Corner exit, I could pull away enter and exiting sweepers and S's but on the 180* corners it was a loading the rear and pushed hard. I dont have a setup sheet filled out yet but will soon. I run Losi red F / yellow R and 4 hole pistons 1.3 all round. 22 / 27.5 . Protek shorty all the way forward. No weight up front ( I am leaning towards that as my problem). Thoughts, I have plenty side bite and forward bit, a stiffer rear spring? Thoughts?
#5102
#5103
Tech Initiate
Thx buddy.
M not too sure if there r shims added, but nonetheless I wil add 1 orc2 more shims as said. Thx again buddy.
M not too sure if there r shims added, but nonetheless I wil add 1 orc2 more shims as said. Thx again buddy.
#5105
R/C Tech Elite Member
iTrader: (520)
Dang, that piece is turning out to be a bugger.. I haven't had a issues with mine rubbing, although the top hole startied to crack, I CA'ed a plastic washer over the hole, and its holding atm..Careful, they are hard to get...lets do a combo order on the TEAM site and split shipping..
#5106
Tech Adept
www.teamsr.co
Hello to All,
My name is Mike Dumas and I am here to represent TeamSR. We do not sell directly to the public. We are encouraging the consumer, you to persuade your local hobby shop to carry our products.
You can now find most of our items from the "Find A Dealer" on the main page of www.teamsr.co
Durango DEX210 Rear Inner Suspension Mounts
DEX210 Carbon Fiber Front & Rear Shock Towers
DEX210 Carbon Fiber Ackerman Rack with optional 4th hole
The hobbyshops below now have in stock the Durango DEX210 Items:
www.gshobby.com
www.absolutehobbyz.com
You may also like to check out our popular Laser Cut Aluminum Off-Road Car Stand from TeamSR.
My name is Mike Dumas and I am here to represent TeamSR. We do not sell directly to the public. We are encouraging the consumer, you to persuade your local hobby shop to carry our products.
You can now find most of our items from the "Find A Dealer" on the main page of www.teamsr.co
Durango DEX210 Rear Inner Suspension Mounts
DEX210 Carbon Fiber Front & Rear Shock Towers
DEX210 Carbon Fiber Ackerman Rack with optional 4th hole
The hobbyshops below now have in stock the Durango DEX210 Items:
www.gshobby.com
www.absolutehobbyz.com
You may also like to check out our popular Laser Cut Aluminum Off-Road Car Stand from TeamSR.
#5107
What are most 9.5T guys running as far as gearing?
I currently have a LRP 9.5 with 81s/25p and my temps after a 15min run was only 104... I am thinking I might be able to get a 28p in there. Outside air temps were high 70's almost 80.
I currently have a LRP 9.5 with 81s/25p and my temps after a 15min run was only 104... I am thinking I might be able to get a 28p in there. Outside air temps were high 70's almost 80.
#5108
Spring Rate chart
didn't know there was a chart already. thanks
Last edited by EvanAZ; 03-29-2012 at 07:42 AM.
#5112
Look what came in from Australia today!!
Pre-orders will start shipping tomorrow.
Pre-orders will start shipping tomorrow.
#5114
#5115
My experience is that the stock spur is the cause of the noise. With RW gears both of our cars are as quiet as anything else on the track.