Durango DEX210 Thread
#4981
They ship out of australia tomorrow so about 10 days or so. More bodies coming too!
#4982
Hi Marcus.
any plans for a front tower?
any plans for a front tower?
#4983
Tech Fanatic
iTrader: (4)
Tried it out today indoors on carpet lots of grip flat etc... wow its not nice driving a car that isn't set up right.
Are you running any rear droop? Is your screw in there at all? My dog bones seem to be very close to falling out so Im thinking about at least running a little
#4984
Tech Master
iTrader: (13)
Yeah you posted that.
Tried it out today indoors on carpet lots of grip flat etc... wow its not nice driving a car that isn't set up right.
Are you running any rear droop? Is your screw in there at all? My dog bones seem to be very close to falling out so Im thinking about at least running a little
Tried it out today indoors on carpet lots of grip flat etc... wow its not nice driving a car that isn't set up right.
Are you running any rear droop? Is your screw in there at all? My dog bones seem to be very close to falling out so Im thinking about at least running a little
Well, the set up is definitely not for carpet...its meant for a med grip clay track. I run full droop all the way around in my 210. Never had an issue with my bones falling out thought the pin is right at the edge of the outdrive at full droop. On carpet you would probably want to take away alot of it. I've never run on carpet, but I know you dont want alot of droop on a high grip surface.
#4985
Yo!
Looking for those lexan gear covers I saw a while back. Please PM me, I would like too buy 2!
Havent been outside of the top three in the A since I have been running this car. My setup is dialed!
Thanks-
Z
Looking for those lexan gear covers I saw a while back. Please PM me, I would like too buy 2!
Havent been outside of the top three in the A since I have been running this car. My setup is dialed!
Thanks-
Z
#4986
Naah, there are already four or five companies making them. I have never broken mine so dont see a need for another one.
check www.RCShox.com for the gear cover pre-order tomorrow.
check www.RCShox.com for the gear cover pre-order tomorrow.
#4987
What is the general feel about rear v med motor mount?
#4988
#4989
Tech Adept
#4990
What's a good starting point for spur and pinion (48p) for an 8.5 on a track that has a straight of approximately 80 feet (25 meters)?
Last edited by Apex; 03-22-2012 at 06:54 AM.
#4992
#4993
#4994
Tech Lord
iTrader: (360)
Diff failure last night, after 1 run. If it wasn't for the fact that I loved how the buggy drove with the shorty pack I just put in it, I would have been possibly be send this buggy to forsale forum.
I'm thinking i've hosed the circlip. Over-squeezed or whatever. its possibly in upside down...After dismantling the complete transmission twice at the track I don't feel like doing it again today.
Didn't feel the need to buy special tools for the build but well thats likely my downfall here.
So. any pointers to a good Circlip Removal Tool ? And will these McMaster-Carr replacements work ? part# 98455108 ? thanks
(Have an SC10 geared diff and HPI shims on order just in case)
I'm thinking i've hosed the circlip. Over-squeezed or whatever. its possibly in upside down...After dismantling the complete transmission twice at the track I don't feel like doing it again today.
Didn't feel the need to buy special tools for the build but well thats likely my downfall here.
So. any pointers to a good Circlip Removal Tool ? And will these McMaster-Carr replacements work ? part# 98455108 ? thanks
(Have an SC10 geared diff and HPI shims on order just in case)
Last edited by tobamiester; 03-22-2012 at 12:09 PM.