Go Back  R/C Tech Forums > General Forums > Electric Off-Road
Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread >

Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread

Like Tree22Likes

Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread

Old 10-16-2013, 03:01 AM
  #14041  
Tech Elite
iTrader: (58)
 
8ight-e's Avatar
 
Join Date: Jan 2009
Posts: 4,175
Trader Rating: 58 (100%+)
Default

Originally Posted by flame56mx
Actually 1/16 is 1.59mm on the chart I have..
correct.. sorry was late :P lol
8ight-e is offline  
Old 10-16-2013, 03:30 AM
  #14042  
Tech Adept
iTrader: (1)
 
thephunnel's Avatar
 
Join Date: Oct 2013
Location: Barrie ON CAN
Posts: 168
Trader Rating: 1 (100%+)
Default

Sorry guys. My bad. The 410R does fit the 25mm lipos if you have the pin in the upper slot. I didn't realize that the rear diff holder had 2 holes for the pin. When I took it apart to drill it out, I found I was in the lower slot. Thanks for your input.
thephunnel is offline  
Old 10-16-2013, 03:33 AM
  #14043  
Tech Adept
iTrader: (1)
 
thephunnel's Avatar
 
Join Date: Oct 2013
Location: Barrie ON CAN
Posts: 168
Trader Rating: 1 (100%+)
Default

Does anyone else have some input on the Reventon pro? I had been thinking of getting the pro/motor combo until the guy at the lhs turned me off of it. He said that he had one and wasn't very pleased with it. He said that he didn't find it very smooth and that the customer service wasn't the greatest. After reading a couple of positive posts on here, I've been thinking about going this route again.
thephunnel is offline  
Old 10-16-2013, 04:26 AM
  #14044  
R/C Tech Elite Member
iTrader: (520)
 
Join Date: Oct 2008
Location: Minnesota
Posts: 7,373
Trader Rating: 520 (100%+)
Default

Originally Posted by thephunnel
Does anyone else have some input on the Reventon pro? I had been thinking of getting the pro/motor combo until the guy at the lhs turned me off of it. He said that he had one and wasn't very pleased with it. He said that he didn't find it very smooth and that the customer service wasn't the greatest. After reading a couple of positive posts on here, I've been thinking about going this route again.
I had a similar experience, I bought 3 of them after they just released them and there was some software issues even with all the updates. I have heard they have them working well now though..
flame56mx is offline  
Old 10-16-2013, 06:02 AM
  #14045  
Tech Master
iTrader: (156)
 
Join Date: Sep 2007
Posts: 1,372
Trader Rating: 156 (100%+)
Default

So no one knows anything about the rear front lrc hanger?
Breeze is offline  
Old 10-16-2013, 07:19 AM
  #14046  
Tech Master
iTrader: (5)
 
ABBOTT's Avatar
 
Join Date: Sep 2008
Location: St Charles ,MO
Posts: 1,207
Trader Rating: 5 (100%+)
Default

I have not tried it and have never seen any feedback on it. Iam curious as well if their is someone that has tried this option.

Been away for a few months, seems people are trying fewer and larger holes for piston setup. Can I get a few thumbs up from those that have tried it.
ABBOTT is offline  
Old 10-16-2013, 07:32 AM
  #14047  
Tech Master
iTrader: (165)
 
Join Date: May 2009
Posts: 1,859
Trader Rating: 165 (100%+)
Default

Originally Posted by thephunnel
Does anyone else have some input on the Reventon pro? I had been thinking of getting the pro/motor combo until the guy at the lhs turned me off of it. He said that he had one and wasn't very pleased with it. He said that he didn't find it very smooth and that the customer service wasn't the greatest. After reading a couple of positive posts on here, I've been thinking about going this route again.
I have a Renventon Pro but have only run it a couple of nights. So far so good. It runs smooth and programming is a breeze with the programming box. My only complaint is that the fan seems to be poor quality. It doesn't seem to want to stay together.
Chris Gierse is offline  
Old 10-16-2013, 09:29 AM
  #14048  
Tech Master
iTrader: (165)
 
Join Date: May 2009
Posts: 1,859
Trader Rating: 165 (100%+)
Default

Is this new?

http://www.team-durango.com/part-inf...artNo=TD402030
Chris Gierse is offline  
Old 10-16-2013, 01:35 PM
  #14049  
Tech Master
 
Dino_D's Avatar
 
Join Date: Aug 2004
Location: Markham
Posts: 1,177
Default

Originally Posted by Chris Gierse
Yeah look like it..

There are a bunch of new parts for the DEX410 kits if you start looking around on the web. From what I have seen on other websites. New U-joints and drive shafts, new front and rear arms (type b), new gearbox (type b), molded cross-pins for the diff.

I am sure there were some photos of the DEX410 seen with u-joints already.

I think most of the type b stuff is mainly a material change, maybe some added rigidity kinda like the 210 type b parts. Not sure about the geometry as I haven't seen any photos. And the Two way slipper which is already out.
Dino_D is offline  
Old 10-16-2013, 02:51 PM
  #14050  
Tech Elite
iTrader: (17)
 
the incubus's Avatar
 
Join Date: Jan 2013
Location: South Florida
Posts: 3,063
Trader Rating: 17 (100%+)
Default

Originally Posted by Chris Gierse
I have a Renventon Pro but have only run it a couple of nights. So far so good. It runs smooth and programming is a breeze with the programming box. My only complaint is that the fan seems to be poor quality. It doesn't seem to want to stay together.
That's surprising about the fan. I'd contact them to se if they send you a new one.

If all else fails MuchMore fans are nice quality and are pretty robust.
the incubus is offline  
Old 10-16-2013, 03:01 PM
  #14051  
R/C Tech Elite Member
iTrader: (520)
 
Join Date: Oct 2008
Location: Minnesota
Posts: 7,373
Trader Rating: 520 (100%+)
Default

Originally Posted by 8ight-e
correct.. sorry was late :P lol
No apology necessary, just didnt want anyone to be drilling 3mm holes in their pistons..lol

Originally Posted by Chris Gierse
I have a Renventon Pro but have only run it a couple of nights. So far so good. It runs smooth and programming is a breeze with the programming box. My only complaint is that the fan seems to be poor quality. It doesn't seem to want to stay together.
The fans are junk, I replaced mine with a Muchmore fan, and that problem went away. I had the Reventon Pro about a year ago, and the software was very sketchy at that time. Had issues with the updates actually installing correctly into the programming box without some type of corrupt file. Think they have ironed things out from what I have seen and heard.
flame56mx is offline  
Old 10-16-2013, 04:26 PM
  #14052  
Tech Regular
iTrader: (19)
 
Join Date: Dec 2011
Location: Florida
Posts: 445
Trader Rating: 19 (100%+)
Default

I purchased a dex410v3 from tower a few weeks ago...price was right....I have it assembled but have yet to put electronics into it. I have a lot going on right now and will sell it due to lack free time to play with it. PM me if interested.
travymoto11 is offline  
Old 10-16-2013, 11:00 PM
  #14053  
ajj
Tech Fanatic
iTrader: (18)
 
ajj's Avatar
 
Join Date: Nov 2010
Location: Sydney
Posts: 893
Trader Rating: 18 (100%+)
Default

Originally Posted by Chris Gierse
Hupo was running these bodies on his cars at the worlds. New cab forward design for the DEX210 as well. Looking at the shape, I guess we are keeping the same layout for the DEX410v4...
ajj is offline  
Old 10-17-2013, 06:25 AM
  #14054  
Tech Elite
iTrader: (17)
 
the incubus's Avatar
 
Join Date: Jan 2013
Location: South Florida
Posts: 3,063
Trader Rating: 17 (100%+)
Default

THough it's likely the best looking cab forward design body, I still think the Khuler body reigns supreme for the 410 and 408. Everything about them is just perfect. Ultra sleek lines with a low roof and all-around killer styling.
the incubus is offline  
Old 10-17-2013, 03:38 PM
  #14055  
Tech Fanatic
iTrader: (9)
 
Konich's Avatar
 
Join Date: Jan 2008
Location: Denver CO
Posts: 972
Trader Rating: 9 (100%+)
Default

^^^You haven't obviously seen the Asharazi bodies then.
Konich is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.