Go Back  R/C Tech Forums > General Forums > Electric Off-Road
Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread >

Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread

Like Tree22Likes

Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread

Old 09-28-2013, 01:11 PM
  #13756  
Tech Elite
iTrader: (99)
 
EvanAZ's Avatar
 
Join Date: Mar 2011
Posts: 2,912
Trader Rating: 99 (100%+)
Default

Just got back from the track where I finally got to run my 410 for the first time. Got some set up changes to make but this thing drives amazing.

Only wish I could drive it like Jorn
EvanAZ is offline  
Old 09-28-2013, 01:20 PM
  #13757  
Tech Elite
iTrader: (27)
 
symmetricon's Avatar
 
Join Date: Jun 2009
Location: houston
Posts: 4,882
Trader Rating: 27 (100%+)
Default

Looks like 3 Durango's in the top ten so far
symmetricon is offline  
Old 09-28-2013, 01:57 PM
  #13758  
Tech Master
 
murky123's Avatar
 
Join Date: Apr 2010
Location: netherlands
Posts: 1,031
Default

50% of the top 6
murky123 is offline  
Old 09-28-2013, 02:18 PM
  #13759  
Tech Elite
iTrader: (17)
 
the incubus's Avatar
 
Join Date: Jan 2013
Location: South Florida
Posts: 3,063
Trader Rating: 17 (100%+)
Default

Originally Posted by ekt
Judging from the Neobuggy pics, it looks like the majority of the car is the same.
Obvious different parts are the chassis, rear bulkheads and the battery holders.


Looks like the rear half has been extended slightly, can fit a shorty in comfortably, the front half is the same as the current car far as I can tell from the pics.

Here's a video of Jorn in practice
+ YouTube Video
ERROR: If you can see this, then YouTube is down or you don't have Flash installed.
I LOL sooo damn hard when I heard the music. I wanted more Cowbell!
the incubus is offline  
Old 09-28-2013, 02:30 PM
  #13760  
Tech Rookie
 
Join Date: Aug 2013
Posts: 12
Default

[QUOTE=Cameron Kellogg;12585439]He ran a 6.5 early but felt under powered. Switched to a 5.5 and then found a good chassis setup. Switched back to a 6.5 for the last round and made the buggy easier to drive thus the TQ time and fast lap over the others.

Also he just TQ'd round 1. Lutz only 2 seconds back from Neumann's time.[/QUOTE

thanks
TeamTapa is offline  
Old 09-28-2013, 03:01 PM
  #13761  
Tech Apprentice
 
Join Date: Sep 2013
Posts: 61
Default

Jörn is also TQ in Q2 and again 3 Durangos in top 10
Maxxi92 is offline  
Old 09-28-2013, 07:54 PM
  #13762  
Tech Elite
iTrader: (19)
 
Join Date: May 2010
Posts: 3,846
Trader Rating: 19 (100%+)
Default

Congrats to Jorn Neumann for grabbing the overall TQ at Worlds. The new DEX410 V4 looks to be working very well, here he is turning some hot laps in practice:http://youtu.be/rF6FnG7FKkM

Edit: looks like this video was posted already, but my phone is not Flash enabled so it doesn't show for me. So here's a link if anyone has the same issue.
Jonny5 is offline  
Old 09-28-2013, 08:58 PM
  #13763  
Tech Champion
iTrader: (45)
 
Cameron Kellogg's Avatar
 
Join Date: Nov 2007
Location: Idaho
Posts: 5,776
Trader Rating: 45 (100%+)
Default

Team Durango drivers put three in the main with Three different chassis setups. Looks like It all works well. Neumann saddle pack v4, Lutz v3, Travis v4 shorty pack. Nice job Team Durango!

On a side note rumor has it that the AE drivers are using Durango diffs converted for their gear boxes.

So another thumbs up for Durango.
Attached Thumbnails Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread-image.jpg  
Cameron Kellogg is offline  
Old 09-28-2013, 09:24 PM
  #13764  
Tech Fanatic
iTrader: (13)
 
Join Date: Mar 2012
Location: Norcal
Posts: 789
Trader Rating: 13 (100%+)
Default

seems Neumann also needs mcmaster pins. :P
another broken&bent pin, while the arm stays strong...

Last edited by nicholasxuu; 09-28-2013 at 09:45 PM.
nicholasxuu is offline  
Old 09-28-2013, 11:22 PM
  #13765  
Tech Elite
iTrader: (17)
 
the incubus's Avatar
 
Join Date: Jan 2013
Location: South Florida
Posts: 3,063
Trader Rating: 17 (100%+)
Default

Originally Posted by Cameron Kellogg
Team Durango drivers put three in the main with Three different chassis setups. Looks like It all works well. Neumann saddle pack v4, Lutz v3, Travis v4 shorty pack. Nice job Team Durango!

On a side note rumor has it that the AE drivers are using Durango diffs converted for their gear boxes.

So another thumbs up for Durango.
Associated factory drivers have been running 410 gear diffs for a long while now. From what I've been told by a few people, they bolt right on though I can't say for sure since I've never tried it.
the incubus is offline  
Old 09-29-2013, 01:51 AM
  #13766  
Tech Addict
 
Join Date: Jun 2012
Location: Austria
Posts: 623
Default

Originally Posted by Cameron Kellogg
?...

On a side note rumor has it that the AE drivers are using Durango diffs converted for their gear boxes.

So another thumbs up for Durango.
Here i found a nice pic on neobuggy, where you can see that!
Attached Thumbnails Team Durango DEX410 4WD 1/10 Off-Road Buggy Thread-image.jpg  
micholix is offline  
Old 09-29-2013, 05:40 AM
  #13767  
Tech Elite
iTrader: (10)
 
rcjunky1's Avatar
 
Join Date: May 2008
Location: Ottawa, Canada
Posts: 2,202
Trader Rating: 10 (100%+)
Default

I'm not sure how many of the ae guys are running durango diffs but some do. A local team driver put them in his car for the worlds, petitrc does a little feature on his car and its listed there, so no secret. Good to see durango doing better in 4wd.
rcjunky1 is offline  
Old 09-29-2013, 05:54 AM
  #13768  
Tech Elite
iTrader: (57)
 
Join Date: Oct 2012
Location: Naperville, IL
Posts: 3,673
Trader Rating: 57 (100%+)
Default

What body are you folks using? Time for a new lid.
shagino is offline  
Old 09-29-2013, 06:22 AM
  #13769  
Tech Regular
iTrader: (29)
 
lil_man72's Avatar
 
Join Date: Sep 2008
Location: raytown, mo.
Posts: 354
Trader Rating: 29 (100%+)
Default

Originally Posted by shagino
What body are you folks using? Time for a new lid.
i've got the jconcepts finnisher being painted right now, but i also think the pro-line bulldog body would be a good choice.
lil_man72 is offline  
Old 09-29-2013, 06:43 AM
  #13770  
Tech Adept
 
rifleman223's Avatar
 
Join Date: Apr 2008
Location: Santa Clarita, Ca.
Posts: 166
Default

Originally Posted by nicholasxuu
seems Neumann also needs mcmaster pins. :P
another broken&bent pin, while the arm stays strong...
Where do you get these pins from?
rifleman223 is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Your Privacy Choices -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.