136LikesTLR 22T 4.0 Race Kit: 1/10 2WD Stadium Truck
12-26-2018, 06:53 AM
#362
22t offset is unique to tlr, unfortunately.
12-31-2018, 10:20 AM
#363
so I haven't raced rc's since the mid 90's with a XXXT, I am looking at getting back into racing and I believe this is the kit I'm choosing, can you guys recommend a good esc and mod motor, not looking to go too cheap, but dont want to break the bank either
Thanks!
Thanks!
12-31-2018, 10:35 AM
#364
My recommendation for something good that doesn't break the bank, is Hobbywing esc / motor and Protek servo.
01-01-2019, 09:30 AM
#365
Will this truck work well in loose dirt situation? Or should the stand up trans be purchased? Does the stand up trans use the same internal parts?
01-01-2019, 08:29 PM
#366
Tech Addict
iTrader: (9)
Diff
The roller i bought came with what looks like a new rtr gear diff take out. Would i be ok to run it at first or just stick with the ball until i can get the aluminium one? Also what would be a good fluid starting point? I have 5k & 7k associated oils at the moment. This would be ran on carpet. Thx.
01-01-2019, 08:36 PM
#367
The roller i bought came with what looks like a new rtr gear diff take out. Would i be ok to run it at first or just stick with the ball until i can get the aluminium one? Also what would be a good fluid starting point? I have 5k & 7k associated oils at the moment. This would be ran on carpet. Thx.
01-03-2019, 08:06 PM
#369
Tech Apprentice
Works great in loose dirt for us. Just needs the brass antisquat block and a gear cover for the laydown transmission to keep dirt out of the gears.
01-07-2019, 07:09 AM
#370
Tech Adept
Looking at the pictures on Facebook from the Carpet Race in Las Vegas, I see non angled ball cups on the front. What partnumber are these? Do I need longer turnbuckles for those ball cups?
Thanks!
Thanks!
01-08-2019, 02:27 PM
#371
bought my kit today, can't wait to get it on the track!
01-11-2019, 07:54 PM
#372
Tech Rookie
Can anyone help me out?
Running on carpet with a tekin 8.5 and tekin rs pro gen 2..gear diff as well 30cst
I ran 1 club race and now something in the tranny/drivetrain is slipping. The trucks motor winds up but the truck barely moves. It's not the slipper cause I've over tightened it and still nothing. When you throttle up the truck you can see the top shaft moving.. I've disassembled the transmission several times and have seen nothing, all the bearings are in place and not 1 gear looks chewed..spins freely with no tough spots . The same for the gear diff nothing looks chewed but it spins freely
Anyone have any tips on what direction I should go
Running on carpet with a tekin 8.5 and tekin rs pro gen 2..gear diff as well 30cst
I ran 1 club race and now something in the tranny/drivetrain is slipping. The trucks motor winds up but the truck barely moves. It's not the slipper cause I've over tightened it and still nothing. When you throttle up the truck you can see the top shaft moving.. I've disassembled the transmission several times and have seen nothing, all the bearings are in place and not 1 gear looks chewed..spins freely with no tough spots . The same for the gear diff nothing looks chewed but it spins freely
Anyone have any tips on what direction I should go
01-12-2019, 05:47 AM
#373
Tech Adept
Check the drive pins on each CVD to make sure you didn't break one. Same goes for the pins behind your sun gears in the diff.
02-03-2019, 02:32 AM
#374
Tech Adept
Do the DE Racing Speedline Wheels fit on the 4.0?
Thanks
Thanks