Project "OMG"
Didn't realize there was a crawler section over here.
http://i674.photobucket.com/albums/v...PAJERO/OMG.jpg |
First and foremost I'd like to thank Andy(exesivefire) for letting me do a clone build of his "WTF" project. I originally saw his build online and was fortunate enough to see it run at the 09 Scale Nats when I attended as a high school graduation gift. Look, when a rig flat out works like his and is so different from the Hilux bodies Velcro'd on a SCX you just gotta love it.
So, my plans are to build a rig similar to exesivefires but also put my own fab/design into it. I typically build low, lots of droop, big tire rigs. I'm shooting for a Go Fast/KOH style rig A big thanks to: P-lo RCPcrawlers The guys over at Socalrcrc.org Equipment I plan to use: Drive train: Rc4wd R2 trans - Rc4wd Transfer case - Mip Drivelines Axles: Axial axles with the standard CVDS - Straight rears - RCP front clockable carriers - Axial highsteer. Electronics: Airtronics RDS8000(crawler) or the MT-4 - LRP 21.5 crawler motor - LRP crawler ESC - Reedy lipos (still debating mah) Tires/Wheels: Proline TSL swampers - Rims are undecided (will need help and ideas on those) Suspension: Proline power strokes front and rear - Rear will be setup with a cantilever style as well. |
Hopefully this will hold you over for now.
http://i674.photobucket.com/albums/v...O/DSC_6363.jpg http://i674.photobucket.com/albums/v...O/DSC_6365.jpg http://i674.photobucket.com/albums/v...O/DSC_6366.jpg http://i674.photobucket.com/albums/v...O/DSC_6369.jpg http://i674.photobucket.com/albums/v...O/DSC_6374.jpg http://i674.photobucket.com/albums/v...O/DSC_6386.jpg Hard to see in the later pictures, but I built up the top/bottom lip so the lexan will sit flush over the lights (leaving no gap for dirt to enter) http://i674.photobucket.com/albums/v...O/DSC_6388.jpg http://i674.photobucket.com/albums/v...O/DSC_6390.jpg Once the bar is painted up, I'll pull the 3m tape off the back and permanently mount the lights inside. http://i674.photobucket.com/albums/v...O/DSC_6391.jpg http://i674.photobucket.com/albums/v...O/DSC_6395.jpg |
Heading over to RCX, but last night I got some work done on the dash and a little GoPro.
http://i674.photobucket.com/albums/v...O/DSC_6262.jpg http://i674.photobucket.com/albums/v...O/DSC_6264.jpg http://i674.photobucket.com/albums/v...O/DSC_6412.jpg http://i674.photobucket.com/albums/v...O/DSC_6401.jpg http://i674.photobucket.com/albums/v...O/DSC_6414.jpg http://i674.photobucket.com/albums/v...O/DSC_6416.jpg Unfinished dash http://i674.photobucket.com/albums/v...O/DSC_6421.jpg |
Earlier today I dropped off the chassis and a hand full of others at the sandblasters(no room here to buy my own blast cabinet).
Anyways, here's some more styrene work. http://i674.photobucket.com/albums/v...O/DSC_6216.jpg http://i674.photobucket.com/albums/v...O/DSC_6233.jpg http://i674.photobucket.com/albums/v...O/DSC_6222.jpg http://i674.photobucket.com/albums/v...O/DSC_6242.jpg http://i674.photobucket.com/albums/v...O/DSC_6243.jpg http://i674.photobucket.com/albums/v...O/DSC_6239.jpg |
Ya got alot more patience than I do. :nod: Looks good! I know styrene can be a headache to work with, but your making great progress.
|
All times are GMT -7. It is currently 12:11 PM. |
Powered By: vBulletin v3.9.3.8
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.