sxx tc spec, air brush +, other bits n stuff
08-10-2010, 05:14 AM
#1
sxx tc spec, air brush +, other bits n stuff
SXX TC Spec ESC - $100 - pending
Selling this cheap as I have used the original bottom of the case to put on my sxx stock spec that I may have ran for a little without the cap on
my stock spec still runs so alls good but you get a bargin with this since its cosmetically not all there. Nothing wrong with this speedy thou cept for the housing issue as you can see the inner bits are still shinny thru the charred hole.
LRP Sphere Competition 2007 ESC - SOLD
Had this forsale the last time I sold stuff but the buyer fell thru so here it is again. Nothing wrong with it.
Xray aluminum option parts - SOLD
Used with custom bearings that allow you to run without needed the plastic bits that come with them. Included is 1 new steering block too.
Airbrush and Compressor - $85 - Sold
both new never used, i have opened it and tested it. Air flows thru the brush and seems fine to me, never used an airbrush ect before, the paper says it needs 30psi the compressor guide goes to 50psi spraying in short bursts it tended to stay around the 30 when I was mucking around with just air, of course if you held it down constant that would plummet.
good for someone learning before deciding to jump into the big boys end of it all.
Prefer pickup with this one as the compressor is as expected quite heavy, will drop off around sydney area for $20
all prices DO NOT include postage, and i can post aussie wide.
pickup avaliable from Zetland, NSW. Postcode 2017 if working out postage.
Selling this cheap as I have used the original bottom of the case to put on my sxx stock spec that I may have ran for a little without the cap on
my stock spec still runs so alls good but you get a bargin with this since its cosmetically not all there. Nothing wrong with this speedy thou cept for the housing issue as you can see the inner bits are still shinny thru the charred hole.LRP Sphere Competition 2007 ESC - SOLD
Had this forsale the last time I sold stuff but the buyer fell thru so here it is again. Nothing wrong with it.
Xray aluminum option parts - SOLD
Used with custom bearings that allow you to run without needed the plastic bits that come with them. Included is 1 new steering block too.
Airbrush and Compressor - $85 - Sold
both new never used, i have opened it and tested it. Air flows thru the brush and seems fine to me, never used an airbrush ect before, the paper says it needs 30psi the compressor guide goes to 50psi spraying in short bursts it tended to stay around the 30 when I was mucking around with just air, of course if you held it down constant that would plummet.
good for someone learning before deciding to jump into the big boys end of it all.
Prefer pickup with this one as the compressor is as expected quite heavy, will drop off around sydney area for $20
all prices DO NOT include postage, and i can post aussie wide.
pickup avaliable from Zetland, NSW. Postcode 2017 if working out postage.
Last edited by Tasmik; 08-15-2010 at 02:24 AM.
08-10-2010, 04:06 PM
#2
Re:xray parts
ygpm
08-11-2010, 03:26 AM
#3
pms replied to
08-11-2010, 04:55 AM
#4
YGPM
08-12-2010, 12:56 AM
#5
couple items sold, other messages replied too.
08-13-2010, 12:55 AM
#6
still forsale
08-14-2010, 12:49 AM
#7
price dropped for remaining items.
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
