Got a few things I would like to sell...
 

G'day,

Got a few thing's I would like to clear out... Make an offer.

2x Futaba S3003 servos, well they are rebadged, one is a colt, the other a duratrax, same specs and same gears/internals as the S3003.
Both need new gears (one striped and the other's output shaft broke), or I could put a new set in one of them.

Have a couple of more servos.
Ace S1903, good condition, works fine.

The other is a throttle/brake servo out of a HPI Nitro RS4 MT, sometimes doesn't center correctly after turning it right.

I also have a Hitec 27mhz 2ch rx that I don't/can't use, it's virtually brand new, only got one run with it. No xtal

I also have a Skyion DSX 3ch tx 27mhz, does not work... I don't know why.
Got to the end of the run (or there abouts) and started beeping saying the batts were flat. I turned it off and turned it back on and it came up with an error after finding out how to clear the error it started doing weird things, will not recognise all inputs (throttle, steering) and the EPA's, EXP and a couple of other things are all whacky, when turning it on if I remember rightly, steering is hard left and about half throttle, this is with everything set to '0'.
It is possible the change all the settings so it points forward and no throttle, but then there is next to no control at all, steering and throttle is virtually
non exsistent.

I have a HSP radio also, bought it with another deal I got a while ago...
No xtal, no ariel (can put one with it, but the end of it is broken).
I havn't used it (it is used, before me). I think it is 29mhz.

Hispeed sp-3820 rx, 2ch, I think it is 29mhz aswell.
Havn't used it either (was used before me), looks like the ariel has been cut/broken.

I also have a Annsmann 5A DC charger for Nimh/Nicad, has deans fitted.

Would anyone be interested in a HPI RS4 Nitro MT Roller (no tyres)? My intentions was to convert it to brushless but won't be able to do that for some time now.
It has a carbon graphite top deck and MIP CVD's.
Also just looking over it the front shock tower has a crack.
If there are any other issues with it I don't know about it... I have not ran it.

I also have a Duratrax Evader ST with Kyosho Prefex 15 brushed esc running a Kyosho 20t single (sealed endbell) that has had a few runs on it, should have a fair bit of life left, has a rustler idler gear, about to pick up the evader one I have ordered, the rustler one has a click, but after running a few runs through it there is nothing wrong with it (not that I can see).
2 new clutch pads (well, one has had about 2 runs on it)
It needs a new spur gear from what I understand as it is not properly pushing up against the clutch pad.
Gladiator tyres on the back, about 70% tread left (rims have seen better days), stock ribbed up front.
Does not come with a radio but I could possibly put one with it.

Will add more when I remember it and/or if I get any interest.
Can upload pics.
Also willing to combine and/or trade some things aswell.
Make an offer.

Cheers.

EDIT:
http://img194.imageshack.us/img194/1...6dt0019.th.jpg

http://img196.imageshack.us/img196/7...6dt0013.th.jpg

http://img141.imageshack.us/img141/4...6dt0035.th.jpg

http://img74.imageshack.us/img74/705...6dt0029.th.jpg

http://img530.imageshack.us/img530/4...dt0028s.th.jpg

http://img411.imageshack.us/img411/3...26dt003.th.jpg

http://img199.imageshack.us/gal.php?g=200907020024.jpg

bump

Negotiable on prices a bit.

bump

Updated and added some pics.

evader st
 

got any pics of the evader????how much $$$???? plus post to perth wa

A few other thing's I forgot earlier...
The top few holes of the rear shock tower has been cut down (previous owner did it to fit another body (can see it in the pics)).
It has 2 bodies, the original and and I think an old proline, both are in pretty good condition.
It has a Futaba S3003 servo in it (futaba badged, not one of the one's above, brand new)

I had a problem with the steering, it kept striping the plastic servo gears every couple of runs. When turning full lock sometimes it wanted to stay at full lock (kinda jams...) takes a little bump or to get moving a bit and it straightens up. I had one of the $40 jacar metal geared servo's in it.
However turning down the dual rate virtually stops it (still doesn't stop it from striping gears, they are plastic after all, they just last longer... usually) at the cost of a tighter turning circle.

It has a deans connector on the esc.
2 extra slipper pads, needs a new spur from what I understand.

Has a rustler idler gear in it, it makes a sound (about 99% sure it is the idler gear), a clicking sound but I have not noticed anything bad performance wise with it. I will be picking up an evader idler gear within the next couple of days and I still have the bearings for that (rustler idler has a different bearing size).

Pulled the ball diff out a couple of runs ago, looks good to me.

I am pretty sure that's everything, if I remember anything else I will post it up.
I don't like to be stung when buying something and the seller neglects to mention some/all faults so I am trying to be as honest as I can.
Let me know if there is anything else you want to know.

http://img359.imageshack.us/gal.php?g=200907010016.jpg

bump

Offers?

Anyone? Anything?
Send me an offer... I might just say yes.

TTT

TTT we go :nod::nod::nod:

:tire::tire::tire:

TTT:nod::nod::nod:

Could also put a metal geared servo with either the Nitro MT or the Evader, not looking to sell it seperately at the moment.

:cry: