OCM Kaos DT-19 build pics +50 Pics
05-16-2007, 10:44 AM
#1
OCM Kaos DT-19 build pics +50 Pics
finished my build and have pics throughout so here they all are.
Last edited by KForce; 09-04-2007 at 06:36 PM.
05-16-2007, 10:45 AM
#2
05-16-2007, 11:01 AM
#5
yes sir i will be in medina on friday morning 
i will be in the little blue trailer pulled by a jeep grand cherokee if you would like to stop by and check out the buggy.
kyle
http://www.ocmracingusa.com
forum http://www.ocmracingusa.com/phpBB
i will be in the little blue trailer pulled by a jeep grand cherokee if you would like to stop by and check out the buggy.
kyle
http://www.ocmracingusa.com
forum http://www.ocmracingusa.com/phpBB
05-16-2007, 07:44 PM
#7
I started this thread on RCCA Zone forums. I havn't updated it lately though.
http://forums.radiocontrolzone.com/s...d.php?t=236394
There is also this thread in the International section here on RCTech.
http://rctech.net/forum/showthread.p...light=OCM+Kaos
Glad to see more interest in the buggy. Speed VSpec...nice!
http://forums.radiocontrolzone.com/s...d.php?t=236394
There is also this thread in the International section here on RCTech.
http://rctech.net/forum/showthread.p...light=OCM+Kaos
Glad to see more interest in the buggy
. Speed VSpec...nice!
05-17-2007, 07:22 AM
#9
awesome i bookmarked both of those also. lots of information in them! i am looking forward to doing the same for the US side of things.
Kyle
Kyle
05-18-2007, 10:03 PM
#10
nice build up ..................... 
05-19-2007, 09:16 PM
#11
how much would you charge to build my OCM buggy...........
05-24-2007, 10:36 PM
#13
awesome!
i did some more running tonight and got the buggy pretty good now.
5000-5000-2000
1.5pistons 40wt losi front 3rd hole down/inside arms slightly above level
1.4pistons 30wt losi rear 2nd hole down/outside arms level
.75 kickup rear
.75 toe inserts rear
0 inserts front toe plate
1 down front upper arms (in the shock tower)
1 up in front rear plate
pillow balls screwed all the way in on bottom arm
-1 degree camber front
-2 degree in rear
middle hole in akerman
2nd hole on steering hubs
rear links middle hole on hubs middle/inside hole on shock tower
front upper arms thin clip between shock tower thick clip in back
i think thats all its a little out of order but i am just looking at the car typing all this heh...i came up with this setup after two weekends or running now and some practice time.
kyle
i did some more running tonight and got the buggy pretty good now.
5000-5000-2000
1.5pistons 40wt losi front 3rd hole down/inside arms slightly above level
1.4pistons 30wt losi rear 2nd hole down/outside arms level
.75 kickup rear
.75 toe inserts rear
0 inserts front toe plate
1 down front upper arms (in the shock tower)
1 up in front rear plate
pillow balls screwed all the way in on bottom arm
-1 degree camber front
-2 degree in rear
middle hole in akerman
2nd hole on steering hubs
rear links middle hole on hubs middle/inside hole on shock tower
front upper arms thin clip between shock tower thick clip in back
i think thats all its a little out of order but i am just looking at the car typing all this heh...i came up with this setup after two weekends or running now and some practice time.
kyle
05-24-2007, 10:46 PM
#14
just some more pics, shes all ready to get dirty again this weekend 
