BANZAI Motors
#3451
Tech Master
OLD DUDES ROCK
#3452
Originally Posted by BanzaiMom
Hey Jay, we're doing fine, except for the pre-Cactus jitters!
How's things in 'Bama????
Judi
#3453
Tech Prophet
iTrader: (34)
Wow I have not been tracking the weather but that is almost down right hot! Got to make sure I have my casper hat to keep my white head protected!
I am getting on a plane in about 3 hours. I will be home soon so I will be on the boards the same times as you guys (and gals) again soon.
I have a couple sets of 2 stage in some tires and some molded foams. We will figure it all out. We will need to put the begging face on and see what we can get when we get there.
I am getting on a plane in about 3 hours. I will be home soon so I will be on the boards the same times as you guys (and gals) again soon.
I have a couple sets of 2 stage in some tires and some molded foams. We will figure it all out. We will need to put the begging face on and see what we can get when we get there.
#3454
I talked to Dawn Sanchez today and she told me they are expecting their shipment of tires from Losi on Tuesday. The track was wet today, probaly from them packing it down. The quad in front of the drivers stand are pretty close together. I wonder if MOD will be doing a triple single.
No one has any tents up or areas marked off yet. See you guys when you get here.
Regards,
No one has any tents up or areas marked off yet. See you guys when you get here.
Regards,
#3455
I am just wondering are guys geting the new team orion 19t turn motors?
#3456
NOPE!!
#3457
I think we know this guy.... If you see him call the authorities he is presumed to be dangerous....... He is known to strap Banzai motors in his RC vehicles.....
http://www.youtube.com/watch?v=6Hp3-Tj29YE
http://www.youtube.com/watch?v=6Hp3-Tj29YE
#3459
That's my Jeremy, and that's why we love him!!
Bring 'er on home Casper!!!!!!!!!
Bring 'er on home Casper!!!!!!!!!
#3461
Tech Elite
iTrader: (6)
Originally Posted by KWHIS
I think we know this guy.... If you see him call the authorities he is presumed to be dangerous....... He is known to strap Banzai motors in his RC vehicles.....
http://www.youtube.com/watch?v=6Hp3-Tj29YE
http://www.youtube.com/watch?v=6Hp3-Tj29YE
#3462
Tech Elite
iTrader: (6)
Originally Posted by nc-hopsing
Cactus is just around the corner!! Casper, hope you had safe/enjoyable flight home. Welcome home!! We'll see you guys in AZ next week!
By the way, I ran that 19T that Dave "turned the com" on for me It ran great Thanks Ryan for the "repair" job
By the way, I ran that 19T that Dave "turned the com" on for me It ran great Thanks Ryan for the "repair" job
Last edited by nc-hopsing; 03-10-2007 at 09:47 AM.
#3463
#3464
Hopsing, yeah, we knew one of them was fast!!
Would have loved
to see Pang's face!!
Johnny S. thanks for the update info!
Judi
Would have loved
to see Pang's face!!
Johnny S. thanks for the update info!
Judi
#3465
Tech Regular
iTrader: (28)
Hello All,
I have taken a few photos of the mods I made to keep my motor from De-Soldering. Attached are a couple of photos for your review. Good luck to the entire Banzai team for racing this season!
I have taken a few photos of the mods I made to keep my motor from De-Soldering. Attached are a couple of photos for your review. Good luck to the entire Banzai team for racing this season!
Originally Posted by vegaskevin
I was having Overheating / De-Soldering problems with my 4wd for a while. I was given some great information at the HodRod race.
After a disappointing 1st round and my motor De-Soldering I went back to my pit and spoke with Frank Root about how I could solve my De-Soldering problem. He took 1 look at my car and told me to cut out my chassis protector where the motor sits. So I did that as well as made a side vent just before where the end bell of my motor is. (Thanks to my buddy Nate for that one).
I never experienced the problem again, plus the temp of my motor is cooler. I'm guessing 40-50 degrees cooler.
After a disappointing 1st round and my motor De-Soldering I went back to my pit and spoke with Frank Root about how I could solve my De-Soldering problem. He took 1 look at my car and told me to cut out my chassis protector where the motor sits. So I did that as well as made a side vent just before where the end bell of my motor is. (Thanks to my buddy Nate for that one).
I never experienced the problem again, plus the temp of my motor is cooler. I'm guessing 40-50 degrees cooler.
Last edited by vegaskevin; 08-15-2022 at 04:47 PM.