Tamiya TB Evolution V
#1561
Tech Regular
Well i got my hands on the 3racing spool for the TB-03 and just went to trail fit it in my EVO V.
Not good news im affraid, just test fitted it into the gear box and there a good 3-4mm of sideways movement without any shims being fitted.
For some reason the spool has just three screw points for the bevel gear where tamiya use four points so holes dont line up and seem to be 0.5-1mm further out on the spool aswell.
Oh well looks like i will wait for the tamiya spool to come out, either that or it will stay an unraced shelf queen .
Not good news im affraid, just test fitted it into the gear box and there a good 3-4mm of sideways movement without any shims being fitted.
For some reason the spool has just three screw points for the bevel gear where tamiya use four points so holes dont line up and seem to be 0.5-1mm further out on the spool aswell.
Oh well looks like i will wait for the tamiya spool to come out, either that or it will stay an unraced shelf queen .
#1562
Tech Apprentice
Well i got my hands on the 3racing spool for the TB-03 and just went to trail fit it in my EVO V.
Not good news im affraid, just test fitted it into the gear box and there a good 3-4mm of sideways movement without any shims being fitted.
For some reason the spool has just three screw points for the bevel gear where tamiya use four points so holes dont line up and seem to be 0.5-1mm further out on the spool aswell.
Oh well looks like i will wait for the tamiya spool to come out, either that or it will stay an unraced shelf queen .
Not good news im affraid, just test fitted it into the gear box and there a good 3-4mm of sideways movement without any shims being fitted.
For some reason the spool has just three screw points for the bevel gear where tamiya use four points so holes dont line up and seem to be 0.5-1mm further out on the spool aswell.
Oh well looks like i will wait for the tamiya spool to come out, either that or it will stay an unraced shelf queen .
#1563
Tech Regular
Ahhhhhhhhhhhhh you may be on to something there as the TB-03 has ball diffs all round. Right just off to strip my car down yet again .
#1564
Tech Regular
Installed with ball diff bevel gear just need to shim it up right and order some more gears so i can put the ball diff back in the rear.
#1565
Tech Apprentice
Hi,
I know this not a 'For Sale-thread', but still I am putting here a link to my eBay-auction, because I am quite sure this should interest all EVO 5-ethusiasts
http://cgi.ebay.com/ws/eBayISAPI.dll...m=120345682551
And if you happen to have any questions or suggestions, please send me a pm.
Tommi.
I know this not a 'For Sale-thread', but still I am putting here a link to my eBay-auction, because I am quite sure this should interest all EVO 5-ethusiasts
http://cgi.ebay.com/ws/eBayISAPI.dll...m=120345682551
And if you happen to have any questions or suggestions, please send me a pm.
Tommi.
#1566
Just asking if anyone tried running Tamiya TB Evo V with LRP Sphere TC Spec ESC with Vector X-11 3.5 turn motor. How was the feel actually? What is the recommendation gear ratio with respect to the provided manual with can go with 30t pinion & 96t spur?
By the way I am using TC Spec with Novak Velocity 4.5 with 34/96. So far so good. However if compare the motor. LRP X-11 rotor is notcy while with novak the car can glide easily when idle.
By the way I am using TC Spec with Novak Velocity 4.5 with 34/96. So far so good. However if compare the motor. LRP X-11 rotor is notcy while with novak the car can glide easily when idle.
#1567
Tech Fanatic
Hey TB Evo Guys;
-My Evo 5 also had a problem with the Rear Upright(Bearing Problem). . . . .I had to install a new Upright and Bearings.-----You guys said something about a Bearing Spacer?. . . . .A spacer can fit in those Rear Uprights?(What`s the item #?).
I`ve tried my best to get My Evo 5 to run just as good as my kits with a Spool.....It runs well now(with an Orion Element Motor).
-But; I will really like to run it with a Spool.
Tamiya is getting OUT-OF-Hand with these total upgrade kits(Evo 5 to EVO 5 MS and TRF 416 to 416 World Edition). The world has no money; why make new platforms? I`m just waiting for a Evo 5 Spool.....Ha Ha!
Merry Christmas. . . . .Happy New Year!
Take Care
-My Evo 5 also had a problem with the Rear Upright(Bearing Problem). . . . .I had to install a new Upright and Bearings.-----You guys said something about a Bearing Spacer?. . . . .A spacer can fit in those Rear Uprights?(What`s the item #?).
I`ve tried my best to get My Evo 5 to run just as good as my kits with a Spool.....It runs well now(with an Orion Element Motor).
-But; I will really like to run it with a Spool.
Tamiya is getting OUT-OF-Hand with these total upgrade kits(Evo 5 to EVO 5 MS and TRF 416 to 416 World Edition). The world has no money; why make new platforms? I`m just waiting for a Evo 5 Spool.....Ha Ha!
Merry Christmas. . . . .Happy New Year!
Take Care
#1568
Hey TB Evo Guys;
-My Evo 5 also had a problem with the Rear Upright(Bearing Problem). . . . .I had to install a new Upright and Bearings.-----You guys said something about a Bearing Spacer?. . . . .A spacer can fit in those Rear Uprights?(What`s the item #?).
I`ve tried my best to get My Evo 5 to run just as good as my kits with a Spool.....It runs well now(with an Orion Element Motor).
-But; I will really like to run it with a Spool.
Tamiya is getting OUT-OF-Hand with these total upgrade kits(Evo 5 to EVO 5 MS and TRF 416 to 416 World Edition). The world has no money; why make new platforms? I`m just waiting for a Evo 5 Spool.....Ha Ha!
Merry Christmas. . . . .Happy New Year!
Take Care
-My Evo 5 also had a problem with the Rear Upright(Bearing Problem). . . . .I had to install a new Upright and Bearings.-----You guys said something about a Bearing Spacer?. . . . .A spacer can fit in those Rear Uprights?(What`s the item #?).
I`ve tried my best to get My Evo 5 to run just as good as my kits with a Spool.....It runs well now(with an Orion Element Motor).
-But; I will really like to run it with a Spool.
Tamiya is getting OUT-OF-Hand with these total upgrade kits(Evo 5 to EVO 5 MS and TRF 416 to 416 World Edition). The world has no money; why make new platforms? I`m just waiting for a Evo 5 Spool.....Ha Ha!
Merry Christmas. . . . .Happy New Year!
Take Care
The item number of the Bearing Spacer is #53891
Here is the link to Tamiya USA
http://www.tamiyausa.com/product/ite...oduct-id=53891
This is a realy must have hop up!
In the later kits, this spacers where already included.
Greetz form Austria, and Merry Christmas