475LikesInspire us. Show me your BEST, CLEANEST electronics installation pics.
03-05-2013, 12:23 AM
#2297
I used 2 layers of pure FasKolor airbrush paint,
Then apply 1 layer of CA
This is all done with an antenna tube, cut at 45deg angle so you get like an old ink pencil. Then strike it along the edge.
I've done more cars like this, search this threath for a couple more, maybe it inspires you.
Regards Robert
Then apply 1 layer of CA
This is all done with an antenna tube, cut at 45deg angle so you get like an old ink pencil. Then strike it along the edge.
I've done more cars like this, search this threath for a couple more, maybe it inspires you.
Regards Robert
03-08-2013, 08:03 PM
#2300
03-09-2013, 08:14 AM
#2301
Here is my 417X
sorry for the crappy phone pic... camera broke down
sorry for the crappy phone pic... camera broke down
03-13-2013, 10:01 AM
#2302
Tech Adept
New WRC STX Touringcar, ready for nats this weekend
03-14-2013, 07:12 AM
#2303
Looks very nice. Good luck for the races 
03-17-2013, 02:43 PM
#2304
.
Last edited by Josh Keller; 04-09-2013 at 04:21 PM.
03-22-2013, 09:02 PM
#2305
I think it's pretty clean.
04-02-2013, 10:22 PM
#2308
Definitely not the cleanest or best looking out of the cars posted here but I still think it's pretty handsome.
My S411 Eryx powered by LRP electronics.
Shell for the 2013 season
My S411 Eryx powered by LRP electronics.
Shell for the 2013 season
04-08-2013, 03:34 PM
#2309
Here is a pic of my VBC Wildfire.
For this one, I rerouted the servo wire so that it exited towards the center of the chassis instead of the left side. I also re-routed the antenna wire and hid it inside of the actual receiver casing itself. I elevated the receiver slightly and mounted my black MyLaps hybrid transponder underneath.
My ESC capacitor was servo taped towards the center of the chassis onto the ESC and fits perfectly between the ESC and battery.
VBC Wiring by IIGQ4U, on Flickr
For this one, I rerouted the servo wire so that it exited towards the center of the chassis instead of the left side. I also re-routed the antenna wire and hid it inside of the actual receiver casing itself. I elevated the receiver slightly and mounted my black MyLaps hybrid transponder underneath.
My ESC capacitor was servo taped towards the center of the chassis onto the ESC and fits perfectly between the ESC and battery.
VBC Wiring by IIGQ4U, on Flickr
04-08-2013, 06:56 PM
#2310
Tech Master
iTrader: (41)
Here is a pic of my VBC Wildfire.
For this one, I rerouted the servo wire so that it exited towards the center of the chassis instead of the left side. I also re-routed the antenna wire and hid it inside of the actual receiver casing itself. I elevated the receiver slightly and mounted my black MyLaps hybrid transponder underneath.
My ESC capacitor was servo taped towards the center of the chassis onto the ESC and fits perfectly between the ESC and battery.
VBC Wiring by IIGQ4U, on Flickr
For this one, I rerouted the servo wire so that it exited towards the center of the chassis instead of the left side. I also re-routed the antenna wire and hid it inside of the actual receiver casing itself. I elevated the receiver slightly and mounted my black MyLaps hybrid transponder underneath.
My ESC capacitor was servo taped towards the center of the chassis onto the ESC and fits perfectly between the ESC and battery.
VBC Wiring by IIGQ4U, on Flickr