USGT
|
|||
#2372
Tech Champion
iTrader: (33)
http://www.rpmrcproducts.com/product...edan/index.htm
I shot them a message a while back which is just one guy (me) making the request, but if everyone on this thread made a request, then perhaps they may see there is large enough of a demand for them to start making them for us
#2373
Tech Master
iTrader: (46)
maybe someone can convince these guys to start making some if there is large enough demand to make it happen:
http://www.rpmrcproducts.com/product...edan/index.htm
I shot them a message a while back which is just one guy (me) making the request, but if everyone on this thread made a request, then perhaps they may see there is large enough of a demand for them to start making them for us
http://www.rpmrcproducts.com/product...edan/index.htm
I shot them a message a while back which is just one guy (me) making the request, but if everyone on this thread made a request, then perhaps they may see there is large enough of a demand for them to start making them for us
#2376
Tech Fanatic
maybe someone can convince these guys to start making some if there is large enough demand to make it happen:
http://www.rpmrcproducts.com/product...edan/index.htm
I shot them a message a while back which is just one guy (me) making the request, but if everyone on this thread made a request, then perhaps they may see there is large enough of a demand for them to start making them for us
http://www.rpmrcproducts.com/product...edan/index.htm
I shot them a message a while back which is just one guy (me) making the request, but if everyone on this thread made a request, then perhaps they may see there is large enough of a demand for them to start making them for us
#2377
Tech Fanatic
Cyclone TC owner's READ THIS
I down loaded a spreadsheet from the USVTA website that calculates Final Drive Ratios for various cars. For the Cyclone TC, this spreadsheet the FDR calculation is incorrect unless you have the 16 tooth center drive gears in your car. My TC has the 18 tooth gears that came in all three TC kits I bought. For the 18 tooth the multiplier should be 2.1667.
#2378
Tech Champion
iTrader: (33)
I ran my 24mm Rides last weekend on 26mm wheels hoping they would work because of the wider variety of offsets available and they hooked up great in the main (once I got the same offsets on the front and rear or the car) and I almost kept up with Bill. BTW Bill, I found the set screw in the pinion came out that's why my car stopped running in the 12 minute main with 90 seconds left.
Sorry to hear you lost a screw, just before the start of the main Wayne lost his during practice too, out of a field of 8 drivers, only 3 finished, it was a brutal race for sure!
Very glad to hear that the 26mm tires are faring well.. I might mount of another set on some 26mm's to see how they work for me too
#2382
Tech Champion
iTrader: (33)
Turnigy TrackStar (old silver can) with a 3Racing heat sink fan combo. My car is currently the 2nd fastest at our local track, well pretty much a 4 way tie in top speed down the back straight with several other drivers. The guy with the fastest motor is running Tekin and I think he's at a 3.3 FDR too.
#2383
Tech Champion
iTrader: (30)
Turnigy TrackStar (old silver can) with a 3Racing heat sink fan combo. My car is currently the 2nd fastest at our local track, well pretty much a 4 way tie in top speed down the back straight with several other drivers. The guy with the fastest motor is running Tekin and I think he's at a 3.3 FDR too.
#2384
Tech Champion
iTrader: (33)
Here is the ROAR approval link:
http://roarracing.org/4rmb/showthrea...tar-9192000034
Regardless, our track doesn't require ROAR approved motors, they abide by Texas EOS Rules which allow any Spec 21.5T motor
http://roarracing.org/4rmb/showthrea...tar-9192000034
Regardless, our track doesn't require ROAR approved motors, they abide by Texas EOS Rules which allow any Spec 21.5T motor
#2385
Tech Champion
iTrader: (30)
Here is the ROAR approval link:
http://roarracing.org/4rmb/showthrea...tar-9192000034
Regardless, our track doesn't require ROAR approved motors, they abide by Texas EOS rules which allow any Spec 21.5T motor
http://roarracing.org/4rmb/showthrea...tar-9192000034
Regardless, our track doesn't require ROAR approved motors, they abide by Texas EOS rules which allow any Spec 21.5T motor